Skip to main content

PS3 upgrade information.

As you all know, the PS3 upgrades are on the way.  I did a PS3 Diesel upgrade for testing last September.   Mike informed me I can now share information and pictures with OGR Forum members.  MTH is now releasing the replacement boards to replace old and worn 5 volt boards.  The platform that MTH is using is the PS3 diesel board with a plug in adaptor board.  This adaptor board allows you to pull out your PS2 5 volt board and plug in this new board.  Your new board will now make your locomotive a PS3 locomotive less the battery and associated hardware.  You will need to load a PS2 3V file or an updeted to 3V 5V file.   MTH is using the diesel board in the conversion and upgrade kit.  To tell the difference on the two adaptor boards, the 5 volt version will have black (HIROSE) connectors and the 3 volt board will have white (CHYAO SHIUNN) connectors.  The part number on the diesel board is AE-1000035.  The 5 volt adaptor board is part number AE-1005v36 and the 3 volt adaptor board is AE-1003v36.  A new heat sink number IC-0000026 is needed. The first few pictures will show the diesel board and adaptor board for 3 volt plugs.  This is what you will see in your upgrade kits.

 

The next picture will show a PS3 board set (bottom) with a PS2 board set to show you they are about the same size.  I will then show the PS3 mounting bracket (top) next to a PS2 bracket.  FYI, the holes line up even with each other.

 

The next picture will show both the 3 volt and 5 volt adaptor boards.  The 3 volt is the one on the top with the white Chyao Shiunn connectors.  The 3 volt board is plugged into the diesel board.  Using the diesel board with the adaptor boards is a good deal as the adaptor board has plugs that go into the diesel board firmly unlike the 40 pin connector on production diesel locomotives.  The next picture will show the adaptor board with the firm plugs.

 

Next two pictures are of PS3 5 volt set ups.  As mentioned earlier, pull your 5 volt board out and plug these in and your engine is now a PS3 engine with the proper or updated sound file loaded in. 

 

The next picture is of a 3 volt adaptor board.  Please notice the two pin plug on top of these 3 volt and 5 volt adaptor boards.  These are not for a battery.  These will be used for later slave connections.

 

The last pictures are of a PS1 Mass Bay F-40 PH.  Original PS1 to PS3.  The PS3 kits will be easier to use than the PS2 kits.  Both PS2 and PS3 share the same speaker and all wiring harnesses.  To do my early PS3 upgrade, all that was needed was to substitute the PS3 board for the PS2 board as in a standard upgrade. 

 

 

I know many will have questions and I will throw out all I know at this point.

 

 

 

P1010289

P1010290

P1010288

ps31 004

ps31 015

ps3 upgrade 012

ps31 034

ps31 002

ps31 021

ps3 upgrade 008

 

 

ps3 upgrade 003

ps3 upgrade 020

ps3 upgrade 023

Attachments

Images (13)
  • P1010289
  • P1010290
  • P1010288
  • ps31 004
  • ps31 015
  • ps3 upgrade 012
  • ps31 034
  • ps31 002
  • ps31 021
  • ps3 upgrade 008
  • ps3 upgrade 003
  • ps3 upgrade 020
  • ps3 upgrade 023
Last edited by Marty Fitzhenry
Original Post
OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
330-757-3020

www.ogaugerr.com
×
×
×
×
×