Skip to main content

Replies sorted oldest to newest

It operates fine in conventional mode with out a problem. This is the second car I have encountered. The first was a caboose that wouldn't light in DCS. The lights were all good. I converted it to LED lighting and now there is no problem. My PW search light car never operated in DCS mode either so it has me stumped. Every single lighted car I have works except these 3 the lights don't even go on.

If you're putting full (~22V) voltage to the track under DCS, is it possible that the car has some kind of protection circuitry that prevents the light from turning on ? 

I have one of these from the 1990s; it had a switched vibrotor coil to rotate the light, and an incandescent bulb which is extremely bright in a typical command control environment.  Yours is a 2014 model.  Since  many folks run command control, MTH may have added some kind of voltage regulator.  I would expect this to be true if the searchlight were lit with LEDs, however the MTH product photo still shows an incandescent bulb.

If possible lower the track voltage a little and try again.  DCS should work fine with 18V AC on the rails.

RRAddict posted:

It operates fine in conventional mode with out a problem.

If your conventional set-up is handy, put engine in neutral and slowly raise track voltage to 18V or whatever.  

Or, lower the DCS track voltage whether by using a TIU variable channel or lowering the TIU Fixed Input voltage if you have a variable transformer.  For this experiment, DCS will operate fine even at ~12V AC.

I like Ted's theory on something voltage related.  After all, when you are not actively sending a DCS command, the DCS track voltage looks like a conventional track voltage signal.

There have got to be some kind of electronic components between the pickup rollers and the bulb.  Was this true of the caboose?  I'm not sure if MTH has begun using 24-volt bulbs, etc.  But if you're going to run it in a command environment, voltage-regulated LEDs might not be a bad way to go.

RRAddict posted:

I have the older car and I have raise the voltage to 16 volts and it operated as it should. I have only 16 volts feeding into the track.

RRAddict posted:

I have 15 volts going to the track and I don't get a blip or flicker. When conventional power is applied it works as it should. I am still stumped.

So to summarize.  16V in conventional works.  15V (or higher) in DCS mode does NOT work.

What are the exact transformers you're using in conventional and DCS?

RRAddict posted:

I am thinking of converting the power going to the car to DC and see if that does anything, any idea what may happen?

If it's the vibrator/buzzing mechanism that spins the searchlight lens, then DC will just generate a lot of heat with no motion.  But as part of this grand science project, it would be interesting to see if the light comes on!

I am using a Z 1000 but I did not convert it to LED, I was going to convert the power to DC. Conventional power comes from a Lionel ZW 275 and the car has no problem. There is no special wiring and everything else works as it should. My PW Searchlight car is in the same boat, doesn't function under DCS but fine in conventional. I have power going to the TIU and out to the track, it's a small layout and nothing fancy like an AIU connected. I will do the DC conversion for tonight.

I checked my searchlight car, #30-7914 from May of 1996. I can't use it, because my DCS system is all 19v pure DC. I connect the TIU to the track in passive mode, through an inductor to keep the DCS signal out of the power supply.
I put the searchlight car on the DSC track, and the light did light up, but there was no rotation because the AC pulses were missing.
Then I placed the car on a test track with only DC, and the light went on. If I connected the positive to the outside rails, there was no light. Then I used an AC transformer for power, and the light came on and rotated.
I disassembled the generator and found a single 1N5391 diode in series with the wire (and on-off switch) to the lamp and the rotation coil. It was wired to allow current to flow only when the center rail is positive.
I applied 10.6vDC to the track, positive center rail, and measured .34amp for only the coil, and .40amp with the lamp also in the circuit. I did not measure the inductance at 60Hz. That would permit less current through the coil if run on AC.
The 1N5391 is an older plain diode, 1.5a at 50v.
Just for the fun of it, I quickly touched the DC power supply lead to the track, and the reflector assembly did turn. This means I could add a 555 timer circuit with output transistor to get the reflector to turn on the DC track power!
Roger

Add Reply

Post
The DCS Forum is sponsored by

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×