Skip to main content

I have had this K-Line Mikado for some time. I use it to pull my semi scale Western Pacific feather boxcars. My collection has grown to well over 20 cars and the engine was nearing its limit. A big part of the problem is the piston type smoke unit driven directly from the motor. These create a lot of drag and rob a lot of power from the motor. I finally got around to replacing the smoke unit with a fan unit. That of course required a new chuff switch to provide the 4 chuffs.

The gear that drives the piston gave me an idea. Its the same gear as the one on the axle so turns the same speed. Rather than install an axle cam I just had to drill and tap 3 more holes for screws to act as cams on a mechanical switch.

Here is before showing the piston attached to the gear.

After the gear mod.

And the result.

 

Pete

Attachments

Images (2)
  • image
  • image
Videos (1)
trim.658A2462-2F21-45C5-93D1-FE4EF1C57C3F
Last edited by Norton
Original Post

Replies sorted oldest to newest

Thanks guys. Its been so long since I ran this engine I forgot I had already put a Cruise M in it. Must have been when Jon first made them. Anyway I replaced the first video I posted here with one with the engine in 100 step mode. The gearing is pretty high as it is and 100 steps calms it down some.

I hope to check pulling power in a few weeks when the club sets up a big layout at the Syracuse show. I am aiming for 30 cars and if it does that I will be happy.

Pete

No sophistication here John. The interface is just a 5v regulator and a double pole reed relay. The switch sends 5v to the relay. One set of contacts goes to the chuff input of the R2LC and the other feeds 5v to the fan motor. If the cam stops on the micro switch the relay is closed and the fan is on.

On this engine there is no wire from the power triac to the smoke unit in the tether. The only control is a switch under the cab. The resistor is a 24 ohm, 5 watt piece connected to the track. Even at 16v its puts out a ton of smoke. This was a quick afternoon project and I didn't really want to get into installing a new tether.

Most of the time smoke will be off. Probably just get turned on for demonstrations. Even at shows I have discovered most people find the excessive smoke objectionble.

I am sorry I didn't order more of these smoke units though as I see it and all of its substitutes are NLA at Lionel. This narrow rectangular unit is the only one I had that would fit is this narrow opening. I will have to check out the MTH units at York.

Pete

 

 

Attachments

Images (1)
  • image
Last edited by Norton

FWIW, I've put the MTH smoke unit in the semi-scale K-Line locomotives.  It's a pretty tight fit, but it does go in there.

I'm curious, if you are feeding the chuff from one side of the switch and the motor from the other side, are the chuffs in sync with the smoke?  I found it interesting that it always stopped with smoke at idle, nice trick.

FWIW, this one is still listed as available at Lionel, looks like the same mechanical fit as yours.  You seem to have one of the "smart" smoke units with the 5-pin connector.  I use the "dumb" ones like below for my conversions, I already have the board for the "smarts".

Attachments

Images (1)
  • mceclip0

Its the relay that is feeding both the R2LC and fan using separate poles which close at the same time so no problem with syncing.

I will have to check my other Lionel units. I may have one of those. The one I used is a semi smart one with all the smarts bypassed.

Still fine tuning. I may turn down the screw heads so micro switch on time is shorter.

Pete

Last edited by Norton
Trainlover9943 posted:
gunrunnerjohn posted:

The Lionel doesn't have the same nifty gear that Pete used for his chuff switch, so that option doesn't exist.

Darn. 

Matt, you can use the smoke unit John pictured. You just have to come up with another chuff switch. John can provide you with another option.

Pete

There are no problems, only solutions.

Last edited by Norton

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×