Skip to main content

Figured out how to have an extra hand for the soldering of the cap to the solder nubs at the top of the board.  Taped the cap to the end of the alligator clip and positioned the ends on the nubs; put some yellow heat shrink over the nubs that I didn't want to touch; took the top of the blow down funnel off to give me more room; needed the QuadHands Helping Hands to help since I don't have the hands of a brain surgeon.  Now I am just waiting on the right size solder and solder tips to show up.  You can just barely see a cap lead tip resting on one of the nubs.  I will do the outside nub first to hold the cap in place.  See pictures.

Attachments

Images (2)
  • blobid0
  • blobid1
Last edited by RickM46

I used .032" diameter 60/40 (3.3% flux) solder.  I had a 1.2 mm bevel point tip in my soldering iron, and it is currently set to 250 degrees C (480 F).  Don't know how accurate it is as it's a used unit I got for free and have no clue when it was last calibrated.  But I just did a lot of soldering with it this last weekend doing the before mentioned DCC install.

sinclair posted:

I used .032" diameter 60/40 (3.3% flux) solder.  I had a 1.2 mm bevel point tip in my soldering iron, and it is currently set to 250 degrees C (480 F).  Don't know how accurate it is as it's a used unit I got for free and have no clue when it was last calibrated.  But I just did a lot of soldering with it this last weekend doing the before mentioned DCC install.

Thanks Sinclair, you have helped out immensely!

I bought the Chinese clone of the Hakko FG-100 calibrator, it's worked quite well for me.  The genuine article goes for $250 or so, but the clone set me back $20.  I've tested it's accuracy with my Fluke temperature probe, and it's quite accurate. It's a mystery how Hakko can charge $100 for the iron and $250 for this little calibrator!  The guts of the calibrator are very simple, it's just a K-Type thermocouple with a circuit to read the temperature and a feature to hold the max temperature.  Big deal!

There are several clones listed on eBay, here's one: eBay 122561208159, it's $20.  You can also just search for Hakko FG-100 and find several more.

 

Attachments

Images (1)
  • mceclip0

Got the capacitor installed and now the Big Boy runs smooth thru all speed steps - go figure.  Many thanks to Gunrunnerjohn, CJack, Zachariah, Alex, StPaul, Sinclair for the info to do the job.  I soldered two 2 inch lengths of 20g wire to nubs 1 (red) and 3 (black) on the board and then the capacitor to those wires.  I located the finished assembly rearward over the motor.  I had to re route the collection or wires going forward over the motor to the left side of the motor.

Since I have never soldered before, I shielded the nubs on the board with heat shrink tubing and put a strip of tape just below the nubs to catch any debris and protect the board.  I did a bit of practicing on 20g wire with .8mm rosin core solder and a Hakko FX888D and a watched a few Youtube videos.  I found after a bit of experimentation the best temp was 585F, tinning the wire AND the solder nubs on the board AND using a long needle soldering tip with tinning worked the best.  Regarding soldering, I have the mind of an artist and the hands of a butcher; the result wasn't pretty but it worked.  If I ever take the shell off again, I might redo some of it.

Thanks for the encouragement gents; I spent nearly 2 hours soldering practice wire and gradually walked the temp up from 550F to 585F to arrive at the best temp.  At that temp, tinning the wire and the tip worked fine.  Attaching the wire to the dry nubs on the board did not work; finally got the idea to tin the nubs too.  Would not have gotten very far without the forum, Hakko, long needle point tip, heat sinks, Youtube, and the QuadHands gizmo.

Last edited by RickM46

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×