Skip to main content

Replies sorted oldest to newest

greg773 posted:

My Dad was just told by Lionel that there is no need to add a 9 volt battery in the new Legacy Milwaukee S3 steamer as we had done I. The past with previous legacy and TMCC locomotives. 

When was this change made? 

When running conventional the battery keeps the sound on when the track voltage goes away. And the track voltage goes away when you stop the engine or reverse the direction. In the case of running Legacy or TMCC, the voltage does not go away, so you do not need the battery.

There is however a rare instance when a particular engine of mine running Legacy is traversing a switch or some part of the track when the engine or tender loses power for an instant. The sound stops running. I have had to restart the engine in that case to bring the sound back. And a battery eliminates losing the sound in that case.

We have a couple of Atlas double slip switches that we get a drop out of sounds if there’s no battery installed. With the battery there is no problem.

The instruction booklet left out the section about adding the battery. He called Lionel and the person on the phone said they had done away with the battery all together.

Unfortunatly, this new loco is dropping out on the switch. 

I know the switch is not the issue. Everything runs fine through it with the exception of Legacy and TMCC that the battery was not installed. 

I don't know that they made improvements, but my VL-BB also doesn't have a battery option.  They use the same sound board as other locomotives with a battery, so one presumes that with the correct cable you could add a battery.  Fitting it into the VL-BB locomotive would be a challenge.   FWIW, the board used supports a battery, here's the one in the VL-BB tender and locomotive, note that both still have the battery provision.

 

 My solution will be to use this when I get around to putting batteries in, I know the guy that makes them.

YLB - RailSounds Battery Replacement

Attachments

Images (2)
  • mceclip0
  • mceclip1
gunrunnerjohn posted:

I don't know that they made improvements, but my VL-BB also doesn't have a battery option.  They use the same sound board as other locomotives with a battery, so one presumes that with the correct cable you could add a battery.  Fitting it into the VL-BB locomotive would be a challenge.   FWIW, the board used supports a battery, here's the one in the VL-BB tender and locomotive, note that both still have the battery provision.

 

 My solution will be to use this when I get around to putting batteries in, I know the guy that makes them.

YLB - RailSounds Battery Replacement

And when you do that, please post a how-to and I will follow suit as my VL BB does drop sound in one place sometimes.  That and It'd be a good example of how to go about it as I have a couple Legacy locomotives that don't have battery provisions that I want to add to.  Maybe a roll your own YLB so it can be split and mounted to fit in odd spaces.

greg773 posted:

It’s 6-84056 #265 

I guess they must have made inprovements to eliminate the battery. Just as long as it doesn’t go over a double slip, lol   

That has been an issue with some Legacy steam locomotives for a while now, unlike the TMCC ones where the sound just begins again when the tender gets power. Too bad they didn't correct this software flaw prior to eliminating the optional battery. Had to purchase the gunrunnerJohn solutions for ours as we didn't want to always be checking on the battery. (Either that or constantly resetting/restarting them) Might be time for some new beta testers there!!

Last edited by BobbyD
greg773 posted:

It’s 6-84056 #265 

I guess they must have made inprovements to eliminate the battery. Just as long as it doesn’t go over a double slip, lol   

Is this number correct?  I think its 6-84065.  Not that it matters.  I could have sworn JonZ @SantaFeFan said, while still at Lionel, that they were making it so if the sound dropped out, on the next chuff it would reset and come back.  Granted I haven't had this issue in a while so I can't say for sure.

Last edited by MartyE

Marty, some of them do come back, others don't.  I can't say which as I've put YLB's in a lot of mine, and I'll be installing them in others as the need comes up.

sinclair posted:

And when you do that, please post a how-to and I will follow suit as my VL BB does drop sound in one place sometimes.  That and It'd be a good example of how to go about it as I have a couple Legacy locomotives that don't have battery provisions that I want to add to.  Maybe a roll your own YLB so it can be split and mounted to fit in odd spaces.

That's not really in the cards, too much work for too little gain.   Most tenders will fit the standard YLB, no reason to scatter it around.

Apparently the rollers are lining up exactly with the dead areas on the switch.

If its feasable , you could try turning one or both of the tender pickup rollers 180 degrees and see if that makes a difference.

I know other members have done this in the past, possibly even with the first run S3

Another option is to run a hot wire from the loco pickup back to the tender pickup. This is obviously a bit more work/ modification.

I've done the tether mod, usually to share the tender pickups with the locomotive on smaller engines.  Stuff like the Legacy Atlantic with only two closely spaced rollers would stall all the time on some switches, adding the tender rollers solves that problem completely.  Quite a few of my small steamers, and even a couple of the larger ones, have that mod.

The new Polar Express still accepts a 9V battery in the tender which I added the second I oiled it up.

One other thing about the Polar Express, it's mentioned in the Instruction booklet that it has whistle steam. Mine doesn't work. I'll probably live with it for now. Any thoughts on how to activate it before I open it up, or is it a fan motor issue?

I ask Dave Olson about eliminating the battery a couple of months ago and he stated the benefits would not be worth the cost of added electronics.  Just be better to add the battery if needed or gets gunrunners charging circuit.  As for these engines that don’t need a battery, maybe due to size and amount of pickup rollers you won’t have drop out issues

Really  though, was it just a space issue on a particular tender, or is the lack of a 9V battery backup a new standard thing? There are a lot of little track issues that can cause a dropping of the tender sounds  which the battery prevents.  I hope they retain the battery generally, or it's a step backwards imo. 

Last edited by pennsy484
gunrunnerjohn posted:
MartyE posted:
gunrunnerjohn posted:

Makes sense, I wonder why they combined them on one switch?

It’s not combined on the Polar. There is still a main on/off and an aux on/off. 

I guess the harness drawing with only three switches is incorrect?

Yes it must be.  Here is the bottom of the lastest Scale Polar Express.  It clearly has both Main and Aux smoke.  Incidentally the manual does not show the Aux smoke switch.

IMG_7410

Attachments

Images (1)
  • IMG_7410

I have sound dropping out on my Atlas Double Switches too.  My Vision Line GG1s both loose sound.  I sent my ATSF 4-8-4 back to Lionel when the factory forgot to put battery cables on it.  The factory was able to add the battery cable.

If the new engines don't have battery cables, I am done buying engines.  My Atlas 90-degree double cross overs also require batteries to make it across two cross-overs.

Sincerely, John Rowlen

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×