Skip to main content

So Lionel shows they still have some of the old RS4 powered motherboards. That's fine and all , but in comparison to the err manual for the old Rail sounds commander there is a slight difference. The Lionel is missing the volume pot and instead has an extra 3 pins next to the speaker connection. My question is what is the wiring situation with the Lionel board compared to the ERR board. I am planning to buy one from Lionel and would like to the know the different wiring for the Lionel one.

Image result for Lionel powered motherboard railsounds diagram

Image result for Lionel powered motherboard railsounds diagram

Image Links:

https://www.lionelsupport.com/...;submitButton=Search

https://www.google.com/search?...mgrc=ULHEG_8lTmEk7M:

Original Post

Replies sorted oldest to newest

Basically the same thing.  The missing three pins on the bottom row in this picture are in parallel with the volume control, with the Lionel model it was designed to be connected to an external pot.  You can actually buy the 10K pot and drop it into the holes and use this like the ERR board.  The documentation for the old RS Commander is useful if you're using this board.  Also, note that the back of the board has a lot of legends for the pins.

If you buy these from Lionel, test them right away, a couple of us got bad ones from Lionel parts and didn't know for months.

Note that these are NOT compatible with the RailSounds 6 modular sound boards, but they work fine with RS4, 5, and 5.5 boards.

Powered RailSounds MBs Front

Powered RailSounds MBs Back

Attachments

Images (2)
  • Powered RailSounds MBs Front
  • Powered RailSounds MBs Back
gunrunnerjohn posted:

Basically the same thing.  The missing three pins on the bottom row in this picture are in parallel with the volume control, with the Lionel model it was designed to be connected to an external pot.  You can actually buy the 10K pot and drop it into the holes and use this like the ERR board.  The documentation for the old RS Commander is useful if you're using this board.  Also, note that the back of the board has a lot of legends for the pins.

If you buy these from Lionel, test them right away, a couple of us got bad ones from Lionel parts and didn't know for months.

Note that these are NOT compatible with the RailSounds 6 modular sound boards, but they work fine with RS4, 5, and 5.5 boards.

Powered RailSounds MBs Front

Powered RailSounds MBs Back

Sounds good, thanks John.

gunrunnerjohn posted:

Basically the same thing.  The missing three pins on the bottom row in this picture are in parallel with the volume control, with the Lionel model it was designed to be connected to an external pot.  You can actually buy the 10K pot and drop it into the holes and use this like the ERR board.  The documentation for the old RS Commander is useful if you're using this board.  Also, note that the back of the board has a lot of legends for the pins.

If you buy these from Lionel, test them right away, a couple of us got bad ones from Lionel parts and didn't know for months.

Note that these are NOT compatible with the RailSounds 6 modular sound boards, but they work fine with RS4, 5, and 5.5 boards.

Powered RailSounds MBs Front

Powered RailSounds MBs Back

Could I use a Lionel 10k pot from another locomotive in this case instead of the mini one.

gunrunnerjohn posted:

Sure, I've extended several of them.  The left hand one has the pot connector for that very reason.  For the old ERR one, I used to extend them to the chassis mounted pot.

Thanks, one other question. I am planning on purchasing your chuff generator. Do j connect the J2 5vDC pin to the 5VDC pin on the railsounds board?

gunrunnerjohn posted:

I'd make REALLY sure that the AC and DC grounds were common, as if they're not, you'll likely cook the Chuff-Generator.  You would probably be all right if you used all three of those connections, but I believe that DC ground may not be common with the frame.

What would you recommend I connect it to if I'm not using a super chuffer?

gunrunnerjohn posted:

Take ohmmeter and measure between the AC ground and the DC ground.  If they're not connected with close to zero ohms, don't use that 5V supply.

Hey John,

I have been working on the engine with the powered motherboard and it working, but the sound seems strange. Whenever a sound like the whistle ends, there is this sort of gargled vibrating sound. Also when that is happening the speaker is moving a lot. Any idea on what is occurring here.

gunrunnerjohn posted:

Yep, we're just turning it up to full volume so that the lower end connection doesn't affect things.  Obviously, if you just connected those two pins at the connector and unplugged the pot, you'd achieve the same result, but the pins are small.

I have done what you said but still the same results. Here is a video to show what is occurring.

Attachments

Videos (1)
VID_20190212_152026139

I've had a few bad boards from Lionel in the last 1.5 years.  Just recently a Lionchief Polar Express board.  Didn't work.  I've got a spare (Frosty the Snowman) board I use to test so I know the engine is good.  I've had them tell me they test them all before shipping - but I'm not totally believing it.  Of course they don't send out bad ones on purpose.

Jim

I don't believe the testing of all the boards before shipment, I've gotten too many bad ones.  Of course, if you look at the older TMCC era boards, they're frequently pulls from old stuff, and I'm sure whatever they came out of had some sort of problem!

When I order boards now, I test them as soon as they come in the door.  Funny thing, when I do that, I get a lot fewer bad boards, it's almost like the gremlins know I'm looking for them!

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×