Skip to main content

Replies sorted oldest to newest

smd4 posted:

There's a big discussion over on RyPN about this incident, and the underlying cause.

There will be a little learning curve for the firemen. There is a difference between firing coal and oil. I suspect that some of the firemen will embrace oil, once they see how much easier it is on them.

 

Matt_GNo27 posted:

https://www.youtube.com/watch?v=tVh0lpmgJ3Q

Doh!

Though I understand and do not fault the D&SNGR's decision to use oil-burners, I got a chuckle out of the comment, "God himself is punishing them for converting coal to oil."

Whatever the cause, it's not because of oil firing.

Rusty

smd4 posted:

There's a big discussion over on RyPN about this incident, and the underlying cause.

There will be a little learning curve for the firemen. There is a difference between firing coal and oil. I suspect that some of the firemen will embrace oil, once they see how much easier it is on them.

 

When burning oil, you need to have the carburetor air mixture screw set a little bit on the rich side.  Too lean, and you risk burning valves and pistons.  

Norton posted:

I appears the piston and cover could be machined relatively easily. Not sure about the piston rings. How would they go about sourcing these?

Virtually every component on a steam locomotive can be re-manufactured, given enough money. We had new combining tubes CNC machined for our Sellers Injectors, but it cost a pretty penny.

Concerning piston rings in general, they are still made:

https://adpistonring.com/steam...ne-piston-rings.html

Last edited by smd4

I would like to learn something from this. It appears to me the piston is turned down from some sort of cast alloy??...if it’s straight up steel....would a chunk of billet steel be an option? Or too cost prohibitive? ....In my world of automotive performance work, we’ll substitute a billet component vs a cast component in a heart beat....way less chance of component failure. Maybe Jack (Hotwater) might lend his expertise on this??....again, I’m on a quest to learn....the only dumb question is the one you don’t ask.........Pat

Kelly Anderson posted:

Pistons of this era are hollow and made of cast iron.  Iron is a better bearing to the cylinder, and if the piston were made of stronger material, then something else would have to break at that moment of "immovable object vs. irresistible force", and many of those other parts are way more expensive than a piston.

Thank you Kelly for the education. I did not know, and what you said makes perfect sense...so if I’ve learned my lesson, y’all rather the piston be the sacrificial lamb than the cylinder or rod, or something really costly...makes economic sense......Pat

Kelly Anderson posted:

Pistons of this era are hollow and made of cast iron.  Iron is a better bearing to the cylinder, and if the piston were made of stronger material, then something else would have to break at that moment of "immovable object vs. irresistible force", and many of those other parts are way more expensive than a piston.

And if I'm not mistaken that immovable object is typically water (condensate or water entrained in the steam from the boiler)?

Lew

geysergazer posted:
Kelly Anderson posted:

Pistons of this era are hollow and made of cast iron.  Iron is a better bearing to the cylinder, and if the piston were made of stronger material, then something else would have to break at that moment of "immovable object vs. irresistible force", and many of those other parts are way more expensive than a piston.

And if I'm not mistaken that immovable object is typically water (condensate or water entrained in the steam from the boiler)?

Lew

Yup. Water is not compressible. If the engine in your car ingests water it's going to bend a piston rod or worse. Same applies to any kind of compression engine. 

Don't know what kind of rules the D&S runs under, but under GCOR the whistle use at 52:28 would not hold up in court if a serious crossing incident had occurred. The D&S would be forking over lots of money. Prosecuting Attorney's are getting more educated by the day concerning RR operating rules and using them against the RR and affected RR employee(s) in a court case.

In today's RR-ing, invasive tech (event recorders, forward cams, cab cams/etc) is seen in a negative light by most RR'ers. I viewed it a bit different: It was my insurance that I would keep my career and financial integrity if something bad (fatality) happened at a crossing or via a trespasser. All I needed to do was comply with the rules and I was covered. Thankfully, I was spared a fatality crossing/trespassing incident in all my years of RR-ing. I did end up in court once, but all was well (see above).

Andre

smd4 posted:

So I watched the video showing the piston failure and the immediate aftermath--should the passengers have been allowed to disembark and congregate around the engine? Up to and including putting a camera basically inside the damaged cylinder? Seems a bit unsafe, considering what happened.

I'd be pretty sure they had the throttle blue-flagged so no chance of live steam entering (and exiting) the cylinder. That would be the only safety issue I could visualize.

Lew

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×