Skip to main content

1. One of my Cab 1's that used to work just fine, now cannot seem to communicate with any engines for some reason. The red indicator led on the command base flickers as usual, as does the led on the Cab 2 base, but nobody is home at the other end. The other Cab 1 works just fine meanwhile. Any ideas as to what is wrong?

2. I was also wondering if there is any way to add a tiny led to a Cab 1 that would glow when it is active, and go out when the Cab 1 has gone to sleep? That way you would know when it is on, and when the batteries are dead, etc., instead of trying to guess what is wrong.

Thanks for any and all thoughts,

Rod

Original Post

Replies sorted oldest to newest

At one time, we had discussed cleaning the contacts on a Cab1.  Some reference here,  but unfortunately the older thread is gone.   If you can get the Cab-1 apart, a dry soft cloth, can be used to re-condition/clean the touch pad contact points.  Aux1 may be the contact most likely to fail first.   I had some success with this on older Cab 1's . IMO   Mike CT 

Some of these Cab 1/Command bases are 20 years old.

Last edited by Mike CT

I just pulled one of mine apart and washed the keypad with a soft brush and soapy water, rinse well.  Dry even better. After blowing dry with compressed air I let it sit out overnight.  Works like new now.  I have also had good luck with TV remotes giving them a bath. But I do keep a bottle of the conductive paint Gunrunner mentioned for hard cases.  J

BobbyD posted:

Rod, does the "bad" Cab1 blow the horn/whistle? I have heard low batteries wouldn't convey the Red speed wheel. Have you tried just the TMCC Cab1 base without the Legacy Cab2 base? (I understand your "Good" TMCC controller currently operates the trains)

Thanks BobbyD, the uncommunicative Cab1 won't blow the whistle or do anything else. It was the good Cab1 that needed the keypad cleaned. Sorry for confusing the issue.

The uncommunicative one makes the base red led flicker with any action including throttle knob, whistle, etc etc. So in my feeble mind I figured that means the batteries are good, the Xtal is seated and doing its thing, and the antenna is ok. There is just no action with any tmcc engine for some reason. Does this make sense? Testing continues.

Rod

@Rod Stewart posted:

I was also wondering if there is any way to add a tiny led to a Cab 1 that would glow when it is active, and go out when the Cab 1 has gone to sleep? That way you would know when it is on, and when the batteries are dead, etc., instead of trying to guess what is wrong.

I read somewhere that the Cab1 goes to sleep after 30 seconds of inactivity, so that should give you a rough estimate of when it is active/sleepy.

@Rod Stewart posted:

Thanks BobbyD, the uncommunicative Cab1 won't blow the whistle or do anything else. It was the good Cab1 that needed the keypad cleaned. Sorry for confusing the issue.

The uncommunicative one makes the base red led flicker with any action including throttle knob, whistle, etc etc. So in my feeble mind I figured that means the batteries are good, the Xtal is seated and doing its thing, and the antenna is ok. There is just no action with any tmcc engine for some reason. Does this make sense? Testing continues.

Rod

Since the led is lighting on the base when you operate the remote it must be getting a signal. But it must be a scrambled signal if it will not operate the train. The base can't be the problem if it works with another remote.  I would still try some new batteries and make sure the contacts are good in the battery box because there really isn't anything else you can do without special equipment to analyze the signal. I have never heard of this problem.

Last edited by iguanaman3

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×