Skip to main content

I just got some new MTH coal hoppers and my plan is to realistic up the coal loads. I purchased some black real fine fish tank gravel that looks like coal. My question is. What type of adhesive should I use to adhere the gravel to the plastic load? Anyone got a suggestion? Do they make a spray on? I’m a woodworker and I’ve used that 3M spray to hold sanding discs on a power sander. I wonder if that would work. Help!

Original Post

Replies sorted oldest to newest

Either plain old white glue or the Tacky Glue will probably work best. Liquid glues will form a better puddle of adhesive and get pulled up into small gaps by capillary action and to a better job of holding irregular-shaped stuff like gravel/coal bits. Tacky Glue's advantage is that, like its namesake, it's tacky and not entirely permanent so it's easy to remove what it's holding and then clean off the residue with water. Traditional white glue holds tighter, but can still be rubbed off/peeled off from smooth surfaces and the rest generally comes up with more vigorous application of water and scrubbing. Pick what seems to be best for your use.

The 3M spray adhesive is great for flat surfaces with a large surface area. (One of its primary uses is as a pressure-sensitive adhesive substitute) How well it works on irregular surfaces varies, often depending on how much liquid you can get to build up so there's enough for the other surface to pick up. On exposed surfaces, it may eventually dry out, loose its adhesive properties and flake away.

Hey Kevin,

I bought some "Aqua" brand, black aquarium gravel at Walmart, and it really looks like coal.  The gravel is heavy plastic, in medium size chunks, and has the same semi-sheen and shape as lumps of dug coal.  It comes in a two- pound bag and is really cheap.

Because the gravel is plastic, I did not want to use white glue to put it down in my hoppers.   Instead, I got a thin piece of flexible styrofoam, and coated the foam with a medium layer of clear silicone caulk (making sure that there was double the amount of caulk down the middle of the sheet than around the edges).  Then I piled the coal on the foam and pressed it down in a realistic mound on the foam.     After I let it dry over night, I looked for any small "holes" or "gaps" in the pile, put a dab of caulk in them, and place a piece of "coal" in it.  No caulk shows through.

After this, I had a sheet with a mound on it, and it was still relatively flexible.   So, I just pushed it down into my hopper cars.

Here's a picture:

P1020448P1020445



The trick to doing this is to carefully measure the length and width of the inside of the hopper car and make sure you cut the foam to those dimensions.  AND,  the ends of the sheet must be cut at an angle, slanting downward, so that the ends fit flush against the insides of the ends of the hopper.  Otherwise, you will be able to see the white foam on the ends when you put the sheet of coal down inside.

As you can see in the first picture, I used the same method to put ballast in two gondolas. 

Once the caulk is totally dry, and you give the sheet a little shake, no more coal or ballast ever falls off of the foam.   And, you can take it in and out of your cars at will.  And, you will not be squirting glue down inside your hopper car.  The weight of the sheet and the firm inside fit against the inner sides of the hopper hold the sheet securely in place.

Perhaps this method may give you some ideas on your project.  I got my thin piece of flexible styrofoam from the inside packaging on a locomotive box.

If I ever decide to put a coal pile in my layout, I'm going to use this plastic gravel, because it really looks like coal.

Mannyrock

Attachments

Images (2)
  • P1020448
  • P1020445

Assuming you are placing the coal on a plastic sheet that fits into the hopper, then white glue on the plastic sheet. Cover with coal and let it dry. After adding more coal use white glue cut in half with water and a few drops of dish soap and spray it on.

I actually use windshield washer fluid to dilute the white glue as it already has the detergent and alcohol to eliminate the surface tension and soaks in better.



FC7505B1-2438-4D53-969D-6F593213D301

937D7031-BE69-4F34-8006-746CBB274B0E


Pete

Attachments

Images (2)
  • FC7505B1-2438-4D53-969D-6F593213D301
  • 937D7031-BE69-4F34-8006-746CBB274B0E
Last edited by Norton
@Patrick1544 posted:

Aileens Tacky White glue. Get it at Michaels.  

Functionally no different than Elmers.  One might say White Glue is White Glue is White Glue.  Get it anywhere. Grocery store, Drug store, Lowes, Home Depot, Walmart, Dollar store.................... Buy a gallon it has a Gazillion uses.  However beware it is not waterproof and will dissolve if wet enough, long enough.  Elmers professional wood glue a yellowish version of white glue is much more water resistant than any white glue and dries "almost" as clear.  Almost as many brands available as white glues also.    j

Last edited by JohnActon

Three rail HO?

Yep.  Marklin back in the fifties had a center rail. Today it still has center rail sliding pickups and tiny contacts on the top of the ties.    I had a girlfriend back in high school who's father had a beautiful 10' x 20'  Marklin layout with center rails.   They moved to the US from Belgium and he brought his trains with them.         j

Attachments

Images (1)
  • marklin XX
Last edited by JohnActon
@JohnActon posted:

Yep.  Marklin back in the fifties had a center rail. Today it still has center rail sliding pickups and tiny contacts on the top of the ties.    I had a girlfriend back in high school who's father had a beautiful 10' x 20'  Marklin layout with center rails.   They moved to the US from Belgium and he brought his trains with them.         j

Yes, I know about Marklin, but it looks nothing like the track in the picture.

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×