Skip to main content

This is the third water tower I have built. The customer specified an extra tall tower (19 inches to the platform base) and an extra wide tank (4 inch dia). This tower is the first pure scratch build. The other two were customized Plastruct kits which incidentally Alan Graziano designed for Plastruct.

Gladish water tower 002

The tank on the left is the kit standard 3.75 inch dia and about 4 in tall. The custom tank is 4 inch dia by about 5 in tall. The platform has been modified to include two 80 mil thick styrene discs. The set that comes with the kit I found to be too thin. The purpose of the second disc is to act as glue surface for the railing. It is important to use a compass to scribe pencil lines on the top and bottom of the platform at the diameter of the tank for accurate placement of the tank and hemispherical bottom. It is also recommended to place pencil marks n the bottom to mark the four locations (0, 90, 180, 270 degrees) for the vertical struts.

Gladish water tower 003

The cone is Plastruct VC-96. It is a little expensive but is thick and very sturdy. Plus I want the lid to be removable so a customer can add or replace a light if desired. The cone could be made much more inexpensively with 10 mil thick styrene. The VC-96 is starts out at 6 inches at the base and can be easily cut down to various diameters. The inside is stepped making cutting very easy. I used an Exacto blade to scribe and break the plastic.

Various 004

Once the tank and railing are glued to the platform. I turned it upside down and glued the bottom of the tank (VHH-400VG). Next glue the legs and let the assembly sit overnight. Note before I glued the bottom to the platform I drilled holes in it plus the platform to accept a TB-16 down tube. The holes are necessary if one wants to add a light to the roof. The TB-16 runs all the way up to the top of the tank so it can act as  a conduit for wires. Note - make sure the opening in the railing lines up one of the leg supports since the ladder will go here.

Cone Top Water Tower 001

Cone Top Water Tower 002

Once the glue for the legs dried it was time for the horizontal bracing (C-6). I cut spacers from hardboard to make sure all the braces lined up.

Cone Top Water Tower 003

Next glue in the diagonal bracing. The kit supplies MR-40 round but I find these kind of flimsy. I used black TB-2 tubing instead since these are plastic coated brass. They help stiffen up the structure considerably especially since I need worry about shipping.

Next up will be finishing the diagonal bracing plus the ladder, drain pipe and base assembly. Hopefully I will these done in the next few days. Below is a picture of this tank along side a 'standard' one I have on my layout. The normal design calls for a 3.25 in diam tank 6 inches high on a platform that is 15 inches high. The small tube on top will house a red flashing LED unit.

Cone Top Water Tower 004

Joe

 

Attachments

Images (7)
  • Gladish water tower 002
  • Gladish water tower 003
  • Various 004
  • Cone Top Water Tower 001
  • Cone Top Water Tower 002
  • Cone Top Water Tower 003
  • Cone Top Water Tower 004
Original Post

Replies sorted oldest to newest

Thank you all

Dave - that tower looks like a worth while project

Alan - my biggest issue due to the height was keeping the legs square. The fact that I cut the legs at 3 degrees instead of the normal 5 degrees helped a lot.

Cone Top Water Tank 005

The tower is completed except for the 'concrete' base. The ladder (KL-8) on the platform is held in place with LC-8 ladder clips. A close up is shown below. The hatch cover came with the kit. It is basically two pieces of 40 mil styrene stock. The piece underneath is smaller that the top piece which offsets it from the tank top.

Cone Top Water Tank 003

Cone Top Water Tank 004

The drain pipe is TB-8 cut at 45 degrees. When you glue it in make sure the lid is on otherwise it may be glued too high interfering with lid placement.

Cone Top Water Tank 001

The ladder from the ground to the platform is glued to strips of C-6. As can be seen from the photos I ran out of black TB-2 tubing so had to finish up with white tubing. I used B-6 I beams to attach the riser pipe to the base. The cap at the bottom is  VHC-24.

The tower is now ready for paint.

Joe

Attachments

Images (4)
  • Cone Top Water Tank 005
  • Cone Top Water Tank 003
  • Cone Top Water Tank 004
  • Cone Top Water Tank 001

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×