C&O 1070 Steam Engine

It may have a Lionel motor and possibly a 726 or 736 chassis, but one thing it's not is Lionel.  The first Mikado Lionel ever made was by Lionel/MPC when they replaced the Berkshire's four wheel trailing truck with a two wheeled truck in 1983 for the Famous American Railroads series #4: Southern Railway.

Most likely scratchbuilt model by a fairly talented modeler, possibly using Walthers parts.

Rusty

Welcome to the OGR Forum, Bob!

This looks like a 2-Rail O scale locomotive, which would use DC power on the rails. It’s not a Lionel product. It has a 2-8-2 wheel arrangement, which means it is a “Mikado” (you were close).

It appears to be a pretty nice model, but I can’t help you with any further details. There are others here who will know more than I do about this model, and they’ll chime in soon.

That all makes sense. I found that it is modeled after an actual engine C&O #1070 from a list of all Mikados that were in the U.S. online. So it is a three rail chassis converted to two rail and built from aftermarket parts. The motor is DC and I haven't tested it yet. I don't have a transformer. I tried a 9 volt dry cell but not a peep. The detail on this locomotive is extraordinary.

The tender looks ok.  That's about as far as I would go - probably an import with Auel trucks.

Lionel started using the "atomic" labeled motor in 1946, I think, and continued it for a few years in several of their steam engines. Could this be a circa 1950 modified Lionel?

@tripleo posted:

Lionel started using the "atomic" labeled motor in 1946, I think, and continued it for a few years in several of their steam engines. Could this be a circa 1950 modified Lionel?

The drive, maybe.  The boiler and tender aren't anywhere close to anything Lionel made in the Postwar era.

Rusty

The valve gear looks "Lionel-ish"; can't quite make out the builder's plate. Nice looking engine...

Mark in Oregon

I don't think there is much Lionel.    It is not in my opinion a Lionel converted to 2 rail.    Lionel did nothing like that in the Postwar era.     Even if a Lionel Berkshire chassis were used, the wheels would have to replaced, or one side insulated for 2 rail.

I think it could be based on a Hines or Pearce kit Mikado.   The valve gear looks too simple to me, but I am not a valve gear expert.    But the tender looks a lot like the Hines tender I have on a mikado.     The water fill hatch casting looks like it is HInes, or All Nation.    The boiler could be from a kit as mentioned or scratch built.    The detail level looks like 50s-70s era to me.

Thanks for the replies folks. The builders plate says Lionel but it's not crisp like I'm used to.

I am repeating myself.  Tender is most likely a brass import.  Locomotive is definitely not Hines, or any other self-respecting relic of the past - Frame does look like Lionel, and drivers could be Lionel re-machined.  Boiler may say Lionel, and may be pieced together from Lionel castings,  but the cab and firebox scream something else (being kind here).  Unless it is of sentimental value, drop the locomotive in the recycling bin, and sell the tender for $100.

Opinion, of course.

@bob2 posted:

Unless it is of sentimental value, drop the locomotive in the recycling bin, and sell the tender for $100.

Opinion, of course.

Oh, I dunno.  It's not an unattractive model.  If it runs, could be a keeper. (I suspect the Lionel Atomic Motor just laughs at a 9v battery...)  There's nothing wrong with "blasts from the past."  If you decide to sell, might be worth something to someone.

Rusty

@Bob Parsley posted:

Thanks for the replies folks. The builders plate says Lionel but it's not crisp like I'm used to.

Probably because there is a couple of layers of paint over the builders plate. It’s not a terrible model. I like the tender. Do you have any idea how good or bad it runs?

Hello,

I have a friend with DC transformers so I can test it soon. Any recommendations on what power it will need? I'd like to put my 3 rail together one day but I won't have any 2 rail so all I can do is test it on the bench. I'll check back when that happens. How do I wire it for test. The brush plate has 5 contacts. If it were 3 rail I'd buy it from my sister, otherwise I can't use it. Thanks again for all the replies. I like this site.

If it has the "Atomic" motor, it's gonna need something more than a lightweight HO power pack...I say this because my wonderful Heathkit pack will run large, open frame DC motors just fine, but will overload trying to power an American Flyer engine...

Mark in Oregon

If its one of the open frame Lionel motors wouldn't an AC transformer like a ZW provide enough power to get it going? I know these will run on AC or DC but they do have a significant amp draw.

You have a very nice looking engine and tender.  Don't scrap it out.  If nothing else - clean it up and make a nice shelf queen out of it.    No one says you need to keep the DC electric motor - it can always be refitted with something else.  You could have someone convert the beast into a command controlled engine also.

You have a very unique, attractive engine. I feel some of the responses have been too critical of your piece.  Enjoy it either if you get it running, or as an attractive display piece.  Very cool!

JohnA

I think its a great looking piece.  Clearly custom and someone put a lot of work into it.  I would display it proudly.

Mine was the only critical response, and I was careful not to slam it too hard.  Indeed I have seen models not much better in the B&O museum in Baltimore - rivets poked freehand with an icepick.

And I collect what most would consider junk - sand cast models in aluminum and bronze.

This is not a model I would display proudly.  To each his own, and opinions are worth what you pay for them.