Skip to main content

Thanks Pat. I was hoping that I didn't bore folks to death with that technical blathering.

I did a major task on the S-38 today by getting those three engine struts soldered to the nacelles. It was touch and go. I didn't know if I would be able to do it and was thinking about epoxying them. At first I was trying to hold them in place while the engines were attached to the wing. I tried welding clamps pushing up on the piece, and then tried using iron wire. Nada! I took the engines off and put their crosspiece in the vice and agin tried wire. Still nada.

I then tried one more thing. I made a metal fixture to hold, loosely, the three pieces. The pins on the nacelle end anchored that end. I just needed to keep the other end in the correct geometry. While this wasn't high tech… it wasn't any tech at all, it did work.

S-38 Engine Struts Fixture 2S-38 Engine Struts Soldered 1

These are solid blocks of bronze and took a long time to get to solder temperature. One of the exhaust pipes fell off, but I put that back after this was done. I did wrap the exhaust pipe with the heat block paste. It protected one of them, but not the other.

I put the engines back onto the wing to see if the struts fit at the correct angles. We'll be away until next week so that's when the struts get soldered to the wing. I will have to protect the big struts that are already in place so they don't de-solder.

S-38 Engine Struts in Position LS-38 Engine Struts in Position R

Here's another view that shows the solder joints. I cleaned them up with the dremel and a dip in the ultrasonic cleaner. They will get painted and it's not a very viewable place on the plane.

S-38 Engine Struts Soldered

There's another set of V braces that go from the main wing to the fuselage. It will not be easy, but I will solder to the wing first with the wing upside down. These plus one more that goes rearward to the fuselage need to attached to the wing before the wing can be joined to the fuse.

S-38 Final Struts

Attachments

Images (6)
  • S-38 Engine Struts Fixture 2
  • S-38 Engine Struts Soldered 1
  • S-38  Engine Struts in Position L
  • S-38 Engine Struts in Position R
  • S-38 Engine Struts Soldered
  • S-38 Final Struts

It most certainly is. I have risen to the challenge and am kicking its butt.

This is a totally different modeling experience than what I'm used to. It's serious metalworking. The fact that 47 years ago I was a metal shop teacher is a good thing. I'm surprised how many things I remember even though I haven't used them for almost 50 years. Example: knocking off the sharp cutting edge on a drill when cutting brass, copper or bronze so the drill doesn't hog in and jam. Brass cutting tools require a negative rake angle. They scrape the metal off and not actually cut it. I'm also happy that I have so many metal capable tools in the shop. Without them, this job would have been a non-starter.

All the engine struts are now in place and the engines are securely soldered to the main wing. I built and installed the V-sharped mid-braces using 2-56 allen cap screws and only broke one 2-56 tap. It caused me to make an emergency trip to the hobby shop to get two more. I re-soldered one of the floats that was hanging loosely. Finally, I was able to drill out the old threads that held the mounting bolts with a "Q" drill and tapped them for an NPS 1/8-27 lamp tube thread. The Q drill was just big enough to totally remove the old threads and provide a clean surface for the new threads.

Using screws relieved me of the worry of de-soldering the struts that were right next to the mid-braces. The tap broke on the second of the four holes. I had completely tapped the hole, tried the screw in it and it didn't go deep enough. Instead of shortening the screw, I attempted to tap the hole deeper. When trying to back out the tap it jammed. Instead of freeing it, I broke it. I drilled another tap drill hole near the old one and re-tapped it successfully.

S-38 Mid Braces

Soldering on this massive bronze structure is still quite a challenge. When it finally hits soldering temp, the entire area is hot and the solder tends to run all over the place. I wish I had that 3000 watt RSU from American Beauty.

S-38 Mid Brace Base

I think my finger got into this picture.

S-38 Mid Brace Screw

I'm going to take the fuselage with these standoffs to the airport and fit it to the globe to make sure it goes on easily. The fuze weighs 20 pounds and is fairly easy to manipulate. The total plane weighs about 50 pounds and will be much harder to handle. I want to verify the mounting before attempting to hold the monster over the globe 8 feet in the air. Note: one of the standoffs is upside down. I just dropped them on to see if the threads were okay.

S-38 Mounting Studs

At the rate this project is going, It should be fully integrated in a couple of weeks. Then it will have to get painted.

I found out recently that the Bronx Victorian article in RMC is being moved from next month to next February (or later). The article was too long and they're no longer going to print multi-part construction features. The editor is having to do some drastic editing (earning his keep so to speak). Their new guidelines for feature articles is between 2000 to 3000 words and 10-15 images. Construction articles can be a little longer. I now have to do some drastic editing. The engine house article is already at 9,600 words with many, many images and it's not yet done. Bummer. I'm not good at writing short (as evidenced by the many thousands of words I've written in this 7 year thread). Mark Twain is credited with saying, "I have to write you a long letter since I don't have the time to write a short one." Moral: tight writing is hard.

 

Attachments

Images (4)
  • S-38 Mid Braces
  • S-38 Mid Brace Base
  • S-38 Mid Brace Screw
  • S-38 Mounting Studs

Couldn't take the fuselage to the airport today for the trial fitting, but I did make some more progress. Got the fuze situated on the build table and trial fit the main wing on top. I also clamped and soldered the tail back on. The tail was one part that hadn't been separated in the great fall. That responsibility fell to me. I had the wing on a couple of stools in the shop. It was behind me when I was working on my little lathe. I rolled back my desk chair and knocked the wing onto the concrete floor. The noise was horrendous and the tail was separated. Luckily, it didn't deform badly and I was able to refit it and solder it back together today. No harm, no foul. One of the struts was slightly out of position and I corrected that too.

I soldered this strut about a 1/4" to close to center and a little bit too far forward. The other struts lined up beautifully.

S-38 Trial Fit of Main Wing 2

I modified my fixture to support the tail during the soldering operation. The tail has some 3/64" bras wire details that I need to replace. These will be easy compared to all the massive parts that needed to be reattached. Notice the model is actually supported by the fancy brass standoffs and lamp pipes. I drilled the base board so they would sink to the proper depth. I then leveled the model and level the main wing. Lines up well. I wanted to add more wood to support the outboard ends of the wings, but frankly, it wasn't needed. Even unsoldered, the diagonal struts were supporting the wing in the proper location. My build board was too narrow to move the supports out the extremis of the wing. The board is my college drawing board that I bolted to the top of an IKEA stool to make an additional work space. It's come in handy many times. It lets me work 360 degrees around the model.

S-38 Trial Fit of Main Wing

With the acetylene air torch soldering has become much more predictable. It's no longer a worry. The joints are coming out relatively clean and well bonded. The repositioned strut now joints the other at the bottom end as it should.

S-38 Repositioned Strut

I used some small C-clamps to lock the tail down tight, applied flux and was able to refuse the previous solder. I just had to add a little bit more to fill some more voids. There are a couple of spots that will need some filler before painting. Two are seen in this image. They're from the two pins that hold up the nacelle tapered end. I cleaned off the wing with baking soda and water to neutralize the acid flux and then went over it with some 240 grit abrasive on an oscillating multi-tool.

 S-38 Tail Affixed

With a successful trial fit I'm quite confident that the entire plane will come together as it should and be quite strong. Once I got the soldering process lined out the project became must less onerous.

Attachments

Images (4)
  • S-38 Trial Fit of Main Wing 2
  • S-38 Trial Fit of Main Wing
  • S-38 Repositioned Strut
  • S-38 Tail Affixed
Last edited by Trainman2001

Eddie, some posts back I asked the gang if they wanted me to continue telling them about the Sikorsky project. They said to keep going, so I did. It has absolutely nothing to do with trains per ce, but it does have to do with modeling and problem solving. These are things that folks have commented on over the last 7 years and why some of them continue to faithfully follow my musings. There's only a couple of weeks of work left on the plane and there will be railroading to follow. For example, the Fairbanks Morse locomotive diesel drawing is a finished as I'm going to make it and it ready to be 3D printed. I have a fellow who wants to buy an HO version of this beast and I'll probably produce an O'scale version too. I'm going to start designing a Baldwin engine also.

FM Loco Design

Attachments

Images (1)
  • FM Loco Design
Last edited by Trainman2001

Miles, Since you are now a renowned expert on the Mars, is it ok if I can ask a question to improve my understanding?

Two related questions, actually:

1) As I understand it, the basic purpose of orienting the model at an angle for printing is so that you never have a larger XY cross-section on the FEP than on the top plate. There is a tug of war between the two, and you want to make sure that the plate always wins. However, I see that you often tilt items even when the shape of the model would permit the largest face to be against the plate. An example is the track bumpers. It seems to me that they could have been printed flat, and with no supports (like the Rook demo) Is there any reason to tilt them, or was it just force of habit?

2) There are cases in which you have small parts that DO have flat surfaces parallel to the plate (the lamp bases, for example), and yet they were still printed with a raft and supports. Wouldn't it be better to print such items directly on the plate?

I guess what I am really wondering is the best approach to printing long, uniform items (skinny or flat). Say I wanted to print a model of something like a railroad tie, which have uniform cross-sections in all three dimensions. Is there any reason to print such a shape at an angle with supports, or is it better to print it flat against the plate with no supports? And if the latter, is it better to put a large or a small face agains the plate?

I hope this isn't too much of a distraction, but I have been studying your model placement choices carefully, and I would like to understand completely.

Last edited by Avanti

Thanks for the support folks! Eddie, if you have the time and the inclination please start at the beginning. The real beginning starts here:

https://ogrforum.ogaugerr.com/...-vs-old-build-thread

It covers the first year of the Saga in the Layout Design Forum starting with the an empty room, painting the walls, covering the ceiling, building the L-girder structure, and then laying track and wiring to get a functioning layout. Part II picks up in this forum and goes from Ballasting to the present day. There are many deviations since I don't work in a linear fashion, periodically digressing to build a plastic kit here and there just to break the monotony. Over the years I've had some steady followers and have learned as much from them as they claim they've learned from me.

Today I did get the fuselage onto the bronze globe for its fitting. It was a good idea to try it out without another 30 pounds of plane hanging on it. It took two of us, me and Jeff Smith (a pilot, architect and member of the Bowman Field Heritage Team) to maneuver it into position and I did have to drill out all three holes in the bronze dome. I broke the cutting edges of the drill so it was shaped better for drilling in brass/bronze. The model will now slip in place when it's complete. The top of the dome is over 7 feet in the air.

S-38 Fit on its Perch

Re: the Mars.

Yes! Putting it on a bias is primarily to limit the contact area to the FEP film. And yes, there are some shapes where maybe situating it flat on the platen might work better. I'm relatively new to this, so it's not quite the expert leading the novice. It's more like a lessor novice leading a newer novice. That said, I also consider positioning faces with more critical details downward so the supports don't make too much of a mess. I also look at hollowed out shapes and want them facing down so the uncured resin drains out of them before I pull them off the machine. I'm trying to remember why I situated the bumpers as I did, but it probably was a compromise of the variables as I saw it at the time. There is no hard and fast rules. The other thing I'm looking at is the supports and where they're attaching themselves. If there are too many on sensitive areas where removal would damage the details I try to reposition. In other words, it all depends...

 

Attachments

Images (1)
  • S-38 Fit on its Perch

I did the first print of the HO version of the FM Loco Primer Mover. Some parts worked well. others not as good. The problem was where I had the supports. I had the engine bottom facing down to promote drainage of the uncured resin, but this put all the supports right on top of all the delicate hatch details on the top crank cover. I tried to remove remnants, but did a lot of damage to the details. I'm reprinting it in a reversed position. Notice though how fantastically the Machine printed those tiny hand grabs on the injector covers. They are tiny. If HO rendered this well, imagine how the O'scale version will look.

FM HO Block Ver 1

The front pump cover came out okay.

FM HO Pump End

The exhaust stacks didn't do so well and I'm reprinting them in a different orientation also. It's never the printer's fault. It's always how you situate parts on the machine.

S-38

Today was a big deal day. I finished putting the last of the support struts on the fuselage. The wing end is soldered. The fuze end was fastened with a 2-56 cap screw into a hole that I drilled and tapped. These six center struts were strong enough to support the fuselage weight. I was able to lift the 50 pound beast up from the build table and set it on the arms of our old knock-off Eames chair, but I am not able to lift it, hold it and position it onto the build table right side up.

S-38 Before the Flip

To do the great reversion I enlisted the help of my daily-growing, 15 year-old grandson. He came over tonight and we were able to turn it and set it properly onto the build table. I've started doing the final cleaning and finishing in preparation for painting. I also added the hanging brace that suspends the tail of the fuselage from the tail booms. This piece is steel wire and replaces another piece of steel wire. We had to cut that wire to release the fuselage from the wing when we removed it from the memorial. All of the rest of the struts (the hot glued ones) had let go and only this wire was holding the mess together. I was pleased that the piece I made ended up being the same length as the wire it replaced indicating that the geometry was still pretty good. Tying the main struts to the lower wing are only four or five more solder joints needed to finish the job. There are some non-load-bearing cross wires that go between the tail booms. I'm going to epoxy these instead of soldering because of their proximity to the hanging brace.

S-38 Four More Joints

Now that it's sitting correctly I find that one strut on one side is a bit long (about 3/32") and on the other side it's a bit short. It wouldn't be hard to de-solder and move the mounting position, but I can't do that with the model in this orientation. It's hard enough to solder this model. It would be near impossible to solder upside down. So I'm going to trim the long one in situ, and either shim the other with a piece of brass or just tie it to the small wing slightly separated from the other strut. The model is over seven feet in the air so no one will ever see the upper surfaces of the small wings.

I epoxied the landing gear so they're ready for paint too. I'm painting them separately and will epoxy them to the plane when it's actually on the dome. They're delicate and will most certainly be destroyed when we're attempting to maneuver the model into position. The props also will go on at the end. This is like my other scratch-build projects. There are no instructions. Much of the thinking is building things in your head to determine the best sequence to do something. You don't want to find yourself having to take something apart to put something in that should have been done before. It's probably the most gratifying part of the job. Someone gives you a beat up piece of junk and a box of unlabeled parts and you have to make it something good. I imagine that a battlefield surgeon is faced with this kind of challenge all the time. What to do before what to get maximum benefit and minimum collateral damage.

The Heritage Team did not believe that the model could be recreated. It's truly a phoenix. Until I solved the solder heat problem I wasn't so sure it was doable either. They are very pleased!

Attachments

Images (4)
  • FM HO Block Ver 1
  • FM HO Pump End
  • S-38 Before the Flip
  • S-38 Four More Joints

The S-38 is mechanically done. I tied the main struts to the small wings. I fixed the slight length deviations by trimming the long one and adding a little chunk of brass under the slightly short one. This was a much easier solution than turning model over again, de-soldering and re-soldering the errant struts in a different position. I also added the cross wires on the tail booms and with that the model was complete. I did some more heavy cleaning. There's still some more to do before painting, but I need to get the right weather since it has to be either outside or in the garage.

S-38 Tail Cross Rods

Props are not glued in. That'll wait until the model is in final position on the memorial.

S-38 Fin Frt

Finally was able to make respectable solder joints. I guess I need to do another to use my newly refined skills.

S-38 Main Strut Rt

S-38 Main Struts Left

The model is very heavy (50 pounds), but quite strong. It will last a long time as long as no one drops it from seven feet in the air onto concrete. With the new mounting system I'm employing, it will not fall down.

S-38 Fin Overhead

It would be nice to keep it natural bronze, but the landing gear are going to have to be painted. So I'm painting the whole thing.

S-38 Fin Right Rear

S-38 Fin Frt

The Bowman Field Heritage Team is very happy with the outcome and they really didn't think it would happen. I wasn't sure it would either. They're planning a big deal for the memorial re-dedication, including newspapers and a presentation by me at the Louisville Filson Historical Society.

So gang, thanks for bearing with me on this diversion. I'm going to get back to the engine house and do the site improvements, fix that strip of LEDs that aren't full brightness and keep working on the machine shop. I'm also planning the next project. Could be the Rick House under construction next to the distillery or the coal mine. I also have another plastic kit on reserve at the hobby shop. It's the Airfix 1:24 scale Hawker Typhoon. I want to build that kit predominantly for the fabulous model of the Napier Saber 24 cylinder double boxer engine that powered it.

I had a successful reprint of the Fairbanks Morse cylinder block. By inverting how it was situated for printing, the highly detail upper crankcase printed perfectly. I still have to remove all the supports, but it should work out fine. You can see the bolts surrounding each hatch. Remember, this in in HO. I've finished the slicing for the O'scale version. If the HO version printed correctly, the O'scale version should be good too. It's too big to do it in one go. In fact, it will take four print sessions. Lost a couple of those microscopic handles, but the fuel filters came out perfect.

FM Reprint

Attachments

Images (8)
  • S-38 Tail Cross Rods
  • S-38 Fin Frt
  • S-38 Fin Left Frt
  • S-38 Fin Overhead
  • S-38 Fin Right Rear
  • S-38 Main Strut Rt
  • S-38 Main Struts Left
  • FM Reprint
Last edited by Trainman2001

The FM engine is complete and ready for delivery. It will have to wait until the person receives back surgery. That will take place in November. The engine came out very nicely. This is premiered. Painting and weathering would really pff it up.

FM HO Finished 1FM HO Finished 2

I'm not going to print an O'scale version unless someone wants one. I don't have an FM engine (yet) so an FM prime mover would be out of character. I do have a Baldwin so I will be producing that engine in O'scale and HO.

The Baldwin is going to turbo-charged and here's a screen shot of the progress. The black lines are my work overlayed over the actual images of the engine. I'm challenged getting the true contours of the cylinder heads. SketchUp doesn't like compound curves very much… at least it doesn't like how I try to draw compound curves.

Screen Shot 2019-10-29 at 9.53.53 PM

Some aspects of the Baldwin engines are easier to draw than EMD, others… not so much. I need to get some imagery of the turbo end of the engine. Right now, this is the only view I have.

Screen Shot 2019-10-29 at 9.53.27 PM

I also moved the S-38 to my photo table after I cleaned off all the detritus and debris left over from the reconstruction and then I took these pictures. It is definitely going to be left in natural metal. I was mixing paint to match the bronze so I can paint the landing gear and props in a more realistic match.

S-38 Finished 3S-38 Finished 2

The color is Tamiya Gold, Tamiya Clear Red and some Tamiya Flat White. I can adjust them to get it even closer. This was my first attempt. There is definitely red in the color, but not as much as copper. This is not the wheel that's going on the model. It was a spare that I printed. My sister, the antique dealer, said, "Don't clear coat it!" I brush painted the test paint. I will airbrush the actual gear.

S-38 Color Match

 

Attachments

Images (7)
  • FM HO Finished 1
  • FM HO Finished 2
  • Screen Shot 2019-10-29 at 9.53.53 PM
  • Screen Shot 2019-10-29 at 9.53.27 PM
  • S-38 Finished 3
  • S-38 Finished 2
  • S-38 Color Match

Myles, That photograph sure puts into perspective the small size of the HO engine.

The Sikorsky S-38 looks great!  A really unique airplane and a unique reconstructive build!  As we have seen before, you have the experience and ability to think out of the box to solve the problems that come up!  Thank you for taking us through this diversion from the layout and it's structures!

Last edited by Mark Boyce

Glad that worked. I didn't have a penny handy.

Had my friend, Stuart Goldberg, over today to take some "real" pictures of the plane with lighting and a very big and spiffy Nikon SLR. He did the fashion shots of the distillery that went into the article. He's also going to shoot the engine house when it's finally all done (including site prep).  I took a cell pic of the setup.

S-38 Photo Setup

You'll notice that I attached the landing gear—loosely—for the shoot. Before the day was over the right side unit fractured at the hub. Very fortunate that this occurred in my basement and not seven feet in the air on the memorial. I will now go to Landing Gear Ver. 3.0. I'm going to machine brass hubs and hinge them prototypically to the strut. They will be soldered to the struts. This should solve the breakage problem. If not, there's always be LG Ver. 4.0, which is resin print with UV investment wax and get the entire gear cast in bronze or brass. I wouldn't use the thick mounting pins since you have to flex the unit to get it into position. In solid metal, it wouldn't flex. I would go back to the original method with small pins and solder the gear to the fuselage. We'll cross that bridge...

You may have noticed over the years that I've been writing this that I practice, "test pilot problem solving". That is when the plane is heading where it shouldn't you, "Try A, try B, try C, D, E, F, etc. until you either level out or augur in." The key is just keep trying stuff. Eventually you will find something that works. Think Edison and the 1,000 light filaments.

Attachments

Images (1)
  • S-38 Photo Setup
Last edited by Trainman2001

Yes indeed!

Baldwin drawings made a milestone. Got those complex heads drawn including most of the injection pump and fuel rack. Still have fuel lines to add. Injector piping itself is going to be too fine to print successfully. I might try just for fun, but don't have high expectations. That odd shadow coming off the middle of the engine is an aberration due to having the engine center below the imaginary horizon line.

BLH Injector Pumps

Had to redo the failed S-38 landing gear. This was version 3.0 and three times is a charm. I machined a new hub out of steel, using, for the first time, my 4-jaw independent chuck for my Taig Lathe. Never chucked up non-round stock before. It worked well, and it's fun. I you really want to get an object dead on, four jaws are actually more accurate with a dial indicator.

I soldered the new hubs to the existing cylinder struts and drilled the wheel hub to accept the turned 1/8" hub shaft.

S-38 Machining LG Hub

The little tails were cut off after this image.

S-38 LG Ver 3

Here are the wheels fully mounted. They're much stronger now. They snap in so securely, I won't have to epoxy them. That resin hub with the holes drilled through it weakened it a lot. The hinge pins on the ends are simulated. I actually thought about making it articulate, but that was silly since the hinges next fuselage are not movable. If the whole deal was metal, one could make them actually retractable. Oh well… All they need now is paint.

S-38 LG in Place LftS-38 LG in Place Rt

Attachments

Images (5)
  • BLH Injector Pumps
  • S-38 Machining LG Hub
  • S-38 LG Ver 3
  • S-38 LG in Place Lft
  • S-38 LG in Place Rt

Happy Friday!

More Baldwin Progress.

I finished the injection pump linkage and piping (don't know it if will print) and then tackled the complex turbo charger and both intake and exhaust runs. I found a pretty sure fire way to do piping in SketchUp by running a single line over the path of the tubing, adding all it's curves and then using FOLLOW ME tool to have a circular profile follow the path creating a smoothly curving tube flow. Running them over and under each other took a bit of fussing.

First pic is the injector rack and fuel piping. Both of these will tie into control systems located at the block front.

BLH Tough Side Drawn

Here's the intake pipe and exhaust spaghetti before adding the turbo to its end.

BLH Induction Tubing Done

Left side of the turbo.

BLH Turbosharger Lft

Right side of the turbo. Generator and exciter go onto the back power-takeoff area.

BLH Turbocharger Rt

This is going to be a terrific O'scale model, but I haven't yet determined the best way to print it. I would certainly not want many supports in that injector area.

While not a 1:1 replication, the engine has the "right" feel. This is an in-line 6. I'm doing an 8. My intake routing is different. Perhaps I'm going to change it.

BLH Turbo Detail Shot Right rear

Attachments

Images (5)
  • BLH Tough Side Drawn
  • BLH Induction Tubing Done
  • BLH Turbosharger Lft
  • BLH Turbocharger Rt
  • BLH Turbo Detail Shot Right rear
Trainman2001 posted:

 This plane is owned by the Johnson's Wax people.

Sikorsky_S-38

Found some very interesting information about the Johnson Wax connection.

"Johnson's Wax used an S-38 as an executive airplane, and it proved itself very useful in a South American exploration flight in search of Carnauba trees.

The company recently commissioned a replica of this airplane and reenacted the trip to South America."

Found this about the airplane in Hawaii:

"The airplane was ideal for inter-island work; four were used for many years in Hawaii."

Sikorsky S-39 float

Last edited by breezinup

Thanks! Until I got this commission I never knew this plane existed since I really never got into the planes of the 1930s. It's a strange bird. You enter the passenger compartment by stepping up the fuselage side and entering through a hatch in the roof going down a short ladder. They were used for exploration probably because they could almost land anywhere and probably had a very low landing speed. There's a good video on YouTube about the restoration of one of these birds.

I did modify that intake trunk. I didn't have to draw that turbo impeller. Found one on the SketchUp 3D Warehouse and adjusted its proportions.

BLH Modified Intake Trunk

Attachments

Images (1)
  • BLH Modified Intake Trunk
Last edited by Trainman2001

The engine part of the Baldwin project is done and ready to be deconstructed for 3D printing. I finished up the oil and water lines yesterday. I'm still deciding on how to divide it up for the most successful printing. I did some more formal rendering using the Podium plug-in on SketchUp.

There are splines on the power output shaft took about 1/2 to draw, but I wanted them there. The fuel line will be printed in two parts separated at the demarcation line at the front plate. I've included supports on both sides of this connection, but the line's really fine and might have a problem.

BLH Comp wo Gen injector sideBLH Comp wo Gan Turbo End

I added more support under the exhaust system to provide more support when printing and beyond. In use, these pipes were insulated to preserve the exhaust energy going into the turbo. I've gotten really good at drawing piping systems on SketchUp. The front plate with the pumps will be printed including those side pipes. One good thing: Whatever I actually draw in SketchUp will faithfully be reproduced in the print output.

BLH Engine Comp wo Gen

I solved the lighting problem in the engine house. It seems that the LED driver chip is sensitive to how the line is loaded. When I cut the positive lead to the side door LED, immediately the lights went to full volume. Just for fun I then attached the bare + lead from the outside light without driver or current limiting resistor to the same spot I just removed the lead with an LED driver attached. Remember, there is an LED driver chip at the front end of this whole string. The outside LED lit normally, but all the other lights went out. When I removed it, the string lit. So there must be something about that light interacting with the front-end LED driver. I then lengthened the + lead and attached it with a 470 ohm current limiter before the first LED driver and everything lit correctly. The arrow shows the current limiter spliced into the + input on that circuit.

EH Lighting Fixed 2

All the lights are now at full output including the outside light.

EH Lighting Problem Fixed 1

Next up for this will be bringing the landscaping up to the EH walls.

S-38:

Painted the landing gear, first with a mixture of Tamiya Gold, White and Clear Red, but it came out like a tan color and i didn't like it. Then I dug out some "Venetian Gold", which is a reddish gold and hand brushed that over top of the airbrushed previous coats (including some Tamiya white primer). I liked it better, and when dry, messed it up a bit with AK Interactive wash. When the wash was removed, it dulled down the "newness" and works reasonably well.

The tone is pretty close especially since the plane's real metal has some many varying shades.

S-38 LG Final 3

The model is over seven feet in the air and will be viewed from a distance so the tonal variations won't be very noticeable. One of the team members suggested re-printing the gear in investment wax (405nm curing) and then get the gear investment cast in actual bronze. I'm going to research that possibility. If they like the gear as is, then it won't be necessary.

S-38 LG Final 4

Attachments

Images (7)
  • BLH  Comp wo Gen injector side
  • BLH Comp wo Gan Turbo End
  • BLH Engine Comp wo Gen
  • EH Lighting Fixed 2
  • EH Lighting Problem Fixed 1
  • S-38 LG Final 3
  • S-38 LG Final 4

I finished the Baldwin VO Engine drawings and prepared them for printing. When I loaded some of the big parts onto the splicer, they seemed really large, almost not fitting the machine. Since the EMD parts fit easily, and most loco prime movers are similar in overall size to fit into similarly sized loco bodies, I suspected something was amiss. I then went back to the main drawing and imported a scale human figure and the engine looked about 12 feet tall. Too big! I was basing the entire drawing on an old scaling I did where the access hatches were 21" in diameter. Last night I found a good cross section of the Baldwin engine on Wikipedia and also found that the bore was 12.5". Using that dimension I scaled the cross section and then compared it to my drawing. I was about 20% too big. I reduced the entire object by that amount and the cross section and my drawing coincided. This represented the third iteration. The second iteration was when I realized that I hadn't hollowed any of the really big chunks to save resin.

This is the correctly sized engine with the generator and a human. It seems about the right size now. I added some supports behind the tiny fuel lines in an effort to hope they'll survive the printing process. I think I went overboard on the belt drive. I couldn't tell how many sheaves there were under the shroud so I just added a bunch. The shroud is all sheet metal and as such lends itself to styrene or brass construction. It's not the strength of resin printing. I left it off. There are also some open spaces on the generator that has screening on it also, which I also chose to simplify.

BLH w Genset

I got back to work on the engine house by doing the back fill using Sculptamold. I prepped the building with Stretch-n-Seal so I could plaster right up to the building without getting it on the building. In this way, the building will still be removable and yet not look so. 

I lifted up the building and got the protector underneath. Sculptamold is good because it holds its shape and fills big gaps easily.

EH Prep for Backfill

I added some Woodland Scenics earth tone tint to kill the white plaster. It's still not earth color, but less visible when chipped. 

EH Backfill Left Side

I may add a skin coat to better feather the STM into the existing terrain. I used the medium putty knife to delineate the walkways to the entry doors.

EH Backfill Rear

While the plaster of paris portion of the STM cures chemically and relatively quickly, the fiber portion has to dewater by drying. Depending on the mass, this drying can take days. I won't do any further work on it until it's totally dry. We have to make an emergency trip to California to attend a funeral on Friday so work on the terrain will wait until Monday.

EH Backfill Rt Side

S-38

I epoxied the props and landing gear on. One of the team members visited yesterday and declared the model complete. I'll keep it at my house until the site prep is finished so nothing bad can happen to it. I'll report on the installation when that occurs.

Attachments

Images (5)
  • BLH w Genset
  • EH Prep for Backfill
  • EH Backfill Left Side
  • EH Backfill Rear
  • EH Backfill Rt Side

Mark, did you have a nice birthday?

Thanks guys!

Printed the first part for the Baldwin VO prime mover. The left side has the exhaust supports, but not the exhaust. I'm printing all the exhausts plus the front turbo plate along with all the cylinder heads and injector fuel feeds. That's printing now. It will be an experiment since it's a complicate part and I'm interested to see if all the surfaces grow properly. This picture was taken in the UV curing chamber. There's a couple of thin section breaks that I'll fix with Bondic.

BLH Left Side in UV Chamber

I also printed another Bridgeport and Engine lathe for the machine shop.  I had a nice lathe until I dropped it. The resin is sufficiently brittle that when it hits the concrete bad things happen. I can make more of them. I also painted the MIG Welder that I printed early on. I wasn't sure if I was going to use it, but it's passable and I don't want to print another. It way too frail to be a practical 3d model without some serious mods.

EH MS Lathe Mill and MIG

Placed in the machine shop they're starting to add some heft to the interior.

EH MS with L M MIG

I then painted the furniture that was also printed long ago when I was learning how to make this thing work. I need more furniture, storage cabinets, and racks for metal stock. I need to get loco parts that can be put on work surfaces and on floors. I want to line the floors with yellow lane markers. I have a small welding table that was a failed print and then redesigned. I haven't printed it again. I still haven't printed a successful standard drill press. The handles on them are really narrow. I will perfect it. I need a bench grinder, work benches with vises. I have an hydraulic arbor press that I will print and I need a better print of the metal cutting horizontal bandsaw. I could also use some suggestions on how to decorate this further. The Bridgeport was actually an older version that lacked a couple of fixes. It's one of the reasons that I'm reluctant to give out the sliced files. I'm never sure if it's the correct one. I've been lax on deleting out of date production files. They're often on one of two thumb drives and sometimes there are duplicates but are really different versions.

EH MS With Some Furniture

Attachments

Images (4)
  • BLH Left Side in UV Chamber
  • EH MS Lathe Mill and MIG
  • EH MS with L M MIG
  • EH MS With Some Furniture

It is quite large. Google the Strassburg RR Steam Shops. There's a lot of good pictures of it and stuck right there in the middle is the wheel lathe upon which I based my freelance design. It's surrounded by more standard stuff. I still have to design and print a vertical turret lathe which is another large machine that would be in such a shop. I also need to put in some kind of jib crane or other material handling system since a lot of the parts are beyond human lifting capacity.

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×