Skip to main content

Hi Everyone, I have 2 questions really.

1) I want to run my conventional engines and DCS engines on the same tracks. I have the MTH Side receiver but and still at lost. Do I wire all my tracks fixed or variable output? Also how do I add conventional engine to the remote.

2) When I start up an ps2 and ps3 engine is there a way to get it rolling without going threw the full PA system?

Any help would be great!

Original Post

Replies sorted oldest to newest

Thanks Guys, 

Paul, I could also do that but I bought a side receiver to enable me to run both with the handheld.

John, I do have Barry's book in paperback and on my tablet, I read both as much as I can, but I still don't understand. I have tried setting all tracks to Z tracks, but if I have a conventional engine on the tracks it just takes off. I know I am missing something! LOL

This is incredibly easy to do. It's in the instructions that come with the TIU.

1. Hook up the transformer you are using to either the Variable 1 or Variable 2 channel input. Connect the wires to the track to the Variable 1 or Variable 2 channel output.

2. Turn transformer throttle to full.

3. Hit the track button on the DCS remote. Select which ever channel the track is hooked up to (Variable 1 or Variable 2 channel).

4. Scroll the thumb wheel up. Voltage to the track increases or decreases if you scroll the thumb wheel down. The direction, whistle, and bell buttons will control your conventional trains. DCS locomotives on the track will ignore all commands unless they are addressed from the remote.

Lou, thank you so much for the information! I will check and make any changes I need to one the TIU and give it a try~! I am guessing if I have 2 conventional engines they will both start and run at the same time. I know it will take a little time for me to get use to it but it sounds like a great way to run both DCS and Conventional!

Thanks again Lou!

Hi Lou, I went out and switched everything from my Z4000 from fixed to var1 & var2. I also switched the input to the TIU and output to the track. I tried and all that happens is the horn blows on the conventional engine and the DCS engine on the same track starts up.

I also get a reading on my Z4000 in the amps window AC. I hove no idea what that means and there is nothing in the Z4000 manual about it.

Any help would be great!~

Last edited by mike g.

Here's the TIU instructions. Go to page 98 for conventional operation wiring, page 113 for conventional locomotive operation:  https://mthtrains.com/sites/de...ction/20as14017i.pdf

There is a 99% chance the reason you are having problems is due to incorrect wiring or incorrect TIU set up. Make sure that the DCS signal is turned on on variable 1 &2. Before I converted a few engines in my fleet to command control I followed the wiring in the TIU instructions for conventional/command operation and had no issues.

Last edited by Lou1985

Hi Mike,

First, I don't have a Z4000 (or it's side remote), I use the Lionel PH-180 bricks for all train running and I have command only, no conventional, so not a lot of experience there.

However, I did try conventional once using the method Lou1985 describes with a variable channel using the thumbwheel to control the conventional train. It worked well, but it was only to briefly test out an old train set my daughter had from 1982. As soon as we saw that the train worked for a few laps, I put the track feeds back to the fixed channels and put the conventional train back in storage. As I recall I used Barry's book to make the changes. That was about 5 years ago.

IMO, I think the easiest way for you to run your conventional engines is the way Paul 2 describes above using the fixed TIU channels and the Z4000 handles. Use the handles to control conventional trains. Then set the handles to 18 volts when you go back to command operation. That should get you up and running fairly quickly. You could at least run your trains until you can sort through the other stuff and get it all up and running the way you would like. 

The 2nd easiest method would be the way Lou1985 describes using the variable channels set to fixed so you can run your command control stuff and using the thumbwheel to control track voltage only for conventional operation. Not a lot more difficult, but that are a few more steps and settings to deal with.

 

Add Reply

Post
The DCS Forum is sponsored by

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×