Skip to main content

I was just noticing that the traditional foam cradle doesn't consider the fact that most engines come apart in two halves. The wheel on a frame and the boiler or diesel shell connected with a bunch of wires. It's almost like the foam cradle for the engine and the small slot for screws was designed by someone who never took an engine apart. When you get the wheels/frame off, it has to be balanced up on the foam with the slot for the screws...which no one uses for screws since a magnetic tray works best for them. Until you get or if you get the wires disconnected, and then lay the shell where? A second engine cradle would be great.

I know I could probably hack one out, but does anyone know of a foam with at least two engine sized cradles parallel and separated by say an inch or so?

Original Post

Replies sorted oldest to newest

I used a Hot Knife I bought at Harbor freight ($15.00) to make mine.  I had enough foam to make two, one for home and one for my club, I used super glue and accelerator to join the pieces.  That was three years ago and neither has come apart.  The piece that was left over I use for the engine shell when I disassemble one.  Recently I found another large piece of thick form under my layout and one of these days I'll make another cradle :-)

 

I have looked at the foam cradles and find the price is way out of site for $1 worth of foam.  I would make a cradle to suit my needs, you can use foam or wood and carpet or whatever you feel will cushion enough. I have used a piece of 5/8 rebound padding with great success. doesn't anyone in O gauge make their own stuff, even the simple stuff like an engine cradle?

I tried to find foam to make my own, I wanted it to be black so it would not look so scruffy after the smoke fluid and oil. I could not find any thing in town. And what I could find at the fabric shop was way over the price of the single cradle one made for trains that I could get from the hobby shop.

If you know of a cheap block of black foam, with the correct stiffness, that's maybe about 16" by 12" by about 3" high, where?

I have had good success cutting foam rubber by using the following technique.  I mark a cut line on the foam with a sharpie.  Next I take a piece of plywood to use as a straight edge and also to compress the foam.  I have the foam to be cut laying on a work bench that is about knee high.  With the piece of plywood on the foam, lined up with the cut line, I take one of my knees and place it on the plywood and press down, compressing the foam.  When I have the foam compressed, I just cut along the edge of the plywood with a razor knife.  this works really good for me. 

gunrunnerjohn posted:
Matt Makens posted:

Leaves a crispy burnt edge on it

Kinda' what I figured from the soldering iron digs in mine.

Mr Union Pacific posted:

I have had good success cutting foam rubber by using the following technique. ... snip...

I'm not sure that would apply to cutting a groove into the foam for a cradle, that works fine for just cutting the foam.

Oh...that's a plan. Buy two blocks of foam and cut strips from one to glue on the other making cradles. Hmmm...

I have a couple of these Engine Cradles that I got a 3-4 years ago. They are pretty nice, can be put together end to end or side by side. They have 35mm film canisters for screws and parts and also a built in trough for parts. Pretty well thought out, at least I thought they were. At the bottom of the page they also have some very nice needle point plastic bottles for oil, smoke fluid or whatever, also got a few of those when I got the cradles. There is other nice stuff on the website as well.

The downside to this is that I have read here on the forum that some have had difficulty contacting Collectors Choice lately. Website is still up, so I am not sure what is going on there? The owner used to own a train store here in the area where I live. He has sold the train store and is now retired. Could be enjoying retirement, traveling or who knows what?

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×