Let us see your Homemade Lionel (or Other) Style Cars you have Made

Post a write up and pictures of Homemade Lionel (or other) style car you have made.  I have made homemade copies of several Lionel cars when I cannot find them or afford them at the time.  I will start with my recently completed Lionel 6413 Mercury Capsule transporting car. 

After looking for a reasonable or inexpensive Lionel 6413 Mercury Capsule transporting car or raised-center flat car body (they are rather hard to find and I have never seen one at a train show) I decided to make one. 

I have the other two center raised-center flat cars.  The first car is the Lionel ACMX 6519 Allis-Chalmers condenser car and it needed a raised-center flatcar deck to handle the tall height of the condenser (made 1958-61).  Then Lionel made the Lionel TLCX 6544 Missile Firing car using the raised-center flat car body from the 6519 (1960-64).  Later, the Lionel TLCX 6413 Mercury Capsule car (made 1962-63) was made from the Lionel Allis-Chalmers Condenser raised-center car body and the Mercury Capsule from the Lionel 3413 Mercury Capsule Launching car Missile.



Here are a couple of the Lionel 6413 Mercury Capsule transporting cars I want to home make.  The slightly aqua green blue car in the front is rarer and brings more money.  Notice the track can be seen in the openings between the two metal straps holding up the Mercury Capsules.

Lionel 6413 aquamarine 1 2-16-2018



 I made the car for zero money.   I found a Lionel 6800 flat car with a broken corner (the plastic  was harder than normal after being stored in the hot attic) and no trucks and wheels.  The second car used was a small Lionel un-numbered flat car complete with trucks in my junk box.  I used plastic from a discarded daily desk calendar base and a plastic paper easel.  I had the glue, blue paint and letter decals and rub-on numbers.  I did get to spend many hours of fun time building the car.




For the body of the Mercury Capsule car, I used the Lionel 6800 flat car upside down to make the raised centered car and cut out the middle of the brown flat car leaving the trucks. 



I band sawed off the ends of the small Lionel flat car with trucks to add to the cars height.  I patched the broken corner of the 6800 car and added plastic to extend the skirts of the trucks.



I decked the top ends of the car with decking left over from the short flat car.  Two small lugs were glued on to the edge to act as hooks for the elastic cord that would hold down the Mercury capsules.  I added in some seams to the side of the raised center car and added skirts to the trucks and extended the raised hump as seen in black plastic in picture below.

I made the rest of the top decking from plastic with holes for the Mercury capsules.  I made the deck a little wider than the car so personal can walk on the deck alongside the capsules.  The Lionel 6413 is wider in the middle than at the ends. 




The Lionel 6413 holds the capsules via two metal brackets across the near bottom of the car with opening from the top to the tracks, presenting a unfinished look.  The Lionel Mercury capsules have cylinder on the bottom to simulate the mercury capsule retro rockets and the capsule is the same one used on the Lionel Mercury capsule rocket with the Lionel  3413 Mercury Capsule Launch Car and Rocket.  The real Mercury capsule would never be transported with the retro rockets attached.  My capsules set on the bottom of the car and the bottom is enclosed, the kind of job one would expect from NASA and the US Government.  The real Mercury capsules are 6 ft in diameter and 6 ft tall and would easily fit in a gondola or box car with wide doors so the Lionel Mercury Capsule cars is a fun item and allowed the use of existing molds to make and sell another interesting car.

My Mercury capsules are made from two toy optical viewers that lets the the grand kids see diamonds moving around when viewed and rotated.  I took out the clear plastic end to make the cones lighter.  I added some heavy paper strips to make the cones look more like they had heat shields on the sides and show the door and window.  The astronaut sits with his back to the bottom heat shield and views through the window.





I painted the car with Model Masters 35183 F  S Bright Blue paint which I had and is fairly close to the Lionel 6413 color.  I then added “NASA” decals as I did not have room or letters for “Mercury Project Cape Canaveral” that Lionel used.  I also added press on numbers of 6413, not as neat as I wanted and all I had room for.  Clear glossy spray was used to seal on the lettering.




I think the Mercury Capsule car came out very well and it can serve as another car and load to use my Gantry Crane for, sort of an action car after all.



Let’s hear from a few of you all car builders about your cars.  I find fixing up a common car into something more special or useful a satisfying part of the model train hobby.  I have several more to share but do not have the pictures of the building process like the 6413.  Most of them are painting and lettering projects.



Photos (12)
Original Post

This isn't quite on your level, but about a year ago, I repainted a 244 Lionel Scout locomotive pink for my oldest daughter in homage to Lionel's "girl's set". I also included diamond rhinestones over the coal load and left "Lionel Lines" visible on the tender.  She ended up loving it Now she has her own to play with her older brother. 



Charlie, your 195Os action packed layout thread inspired me to go forward and get a modest layout up and running in a 5x9 space. Thanks again for sharing all of your great ideas. 




Photos (2)

Another homemade car was a Gold Bullion car.  Windows were cut in both sides with a Dremel Moto tool with saw blade and a razor saw and plastic windows were added.  Gold bars were made from kitchen match sticks painted gold.  Two 12v or 7v in series mini Christmas lights were added, a feature the Lionel version does not have.  A light pick up was made from brass shim stock.

Gold Bullion car 4-20-2016 001


Detail of homemade Pickup is below.  A piece of tin can was added to improve durability of shim stock.

Gold Bullion car 4-20-2016 008

Come on you closet Homemade car fans, lets see them.


HEre are some Custom Jobs done:


K-line MP15 Switcher


Complete with Full cab interior


Custom N.T.T.X. 5 unit Container Spine car. 


The White Spine unit is what this car was originally developed from. 


Custom Built [and not by me] PRR NA cabin car with complete interior


PRR Custom built XM Boxcar - All wood Construction


PRR NDa made from a Gloorcraft 4 wheeled ND kit.

member:Golden Spike Club Charter Member


Photos (14)

Add Reply

OGR Publishing, Inc. PO Box 218, Hilliard, OH 43026 330-757-3020