Skip to main content

Hello -

I'm new to this forum, and I joined in the hope that someone here can help me with a technical question. I recently acquired a Lionel 773 Hudson (1950 version) and it runs great, but there's an issue with it. The smoke element gets hot and smoke will rise from the stack in a thin wisp when parked in neutral, but the smoke lever doesn't operate when the loco is running (no puffing smoke). I took a close look at it last night, but I can't see where there's anything to push the smoke lever forward when the crosshead moves forward. There's a little tab where the piston rod goes into the cylinder that looks like it's purpose is to move the lever backwards, but I can see nothing that would move the lever forward. I have a 726 (1946 version) that has a special longer crosshead bolt on one side that is used to push the smoke lever forward on it, and I realize the two locos are very different, but is it possible that the 773 should have a similar arrangement? Maybe someone serviced it and put in the wrong length bolt? The smoke lever moves freely if I reach in with a small screwdriver and operate it manually. My Greenberg's Repair Guide is an older version, and for some reason contains no info on the 773 (I see that the current version has it), so I'm really in the dark here. I'm hoping that someone here can tell me what actually moves the smoke lever forward on this engine.

Thanks,

Tom West

Original Post

Replies sorted oldest to newest

There is a tang on the left hand crosshead that pushes the smoke lever with the arm down. The smoke lever the pushes the  piston inside the cylinder of the smoke unit. So most likely the tang on the crosshead is bent or missing or the piston cup is stuck in the cylinder or missing. Another source of the problem is a blocked air port in the pellet cup from too many pellets. The tang on the crosshead is to move the smoke lever forward, not back, that  happens with gravity.

Last edited by Chuck Sartor

You need the service manual for the 773. It illustrates the locomotive fairly well.  It has been published in a number of the service manual reprints.

Another potential issue with 773 smoke is that there is a recess cast into the steam chest for the smoke lever.  Many of the smoke levers were not well formed and do not interface with the steam chest well.  This results in the smoke lever having very short travel, which produces very little smoke piston travel.   A proper smoke lever was sold for many years, but I have not seen one recently.

Thanks to all who replied. Last night I took another look at the 773 and the tang on the left-hand crosshead is there; I'd seen it the first time I looked at it but it was ahead (meaning forward) of the smoke lever, so the as it moved back and forth the smoke lever was just hanging straight down doing nothing. The tang also looked like it had slid forward 1/8 - 3/16" or so on the crosshead shaft (or piston rod on a real locomotive). As I operated the smoke lever manually back and forth with a small screwdriver, when it was as far forward as it would go, it looked like if the tang was behind the lever, it would jam the crosshead not allowing it to travel far enough forward. This was confirmed last night; as I took a closer look at it, it now looked as though the tang was far enough back on the crosshead shaft to fit behind the smoke lever. I tried fitting the crosshead with the tang located behind the smoke lever, operating it by hand before I reconnected the main drive rod to the center drive wheel. It seemed to operate okay, so I reassembled the rods and tried it on the track under power. The loco only moved a short distance forward before the left-hand side rods jammed to the point that the piston shaft with the tang on it was pulled completely out of the crosshead. I disassembled the crosshead and gently tapped the shaft back into place, but something is still definitely wrong. I feel that I'm on the right track now, but now I'm wondering if the smoke lever needs to be "adjusted" (meaning carefully bent forward to allow it to travel farther forward), or maybe there's something limiting the upward travel of the smoke unit piston. I'm going to have to remove the boiler shell from the frame and take a look at the smoke unit itself to check for anything that might be amiss.

Add Reply

Post
This forum is sponsored by Lionel, LLC

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×