Skip to main content

I'm having an issue with my transformer. I believe the item number is AH601. I had a derailment and now I have no power on the left side of the transformer until I hit the direction key just the right way but its momentary. Any ideas? The circuit breaker never did trip when the train derailed. 

Attachments

Images (1)
  • 20200528_162926
Videos (1)
20200528_162942
Original Post

Replies sorted oldest to newest

These transformers have an internal fuse- in your case two fuses. Its possible that you blew the fuse before the c.b. tripped. 

If the screws holding the transformer casing are not of a common type, you may have to send it back to mrc for fuse replacement.

Wonderful. I'll peak at the underside and see what kind they are. Btw, I should've mentioned. I use both DCS and legacy. 

Remove the boards with the diodes and yellow plastic strips on the left side. Flip it over and check all three copper tabs very carefully where they are soldered to the board. Look for failed solder joints and broken contacts. This is a known issue with these transformers. I have the PP Dual and the PP. Both of mine have had this failure and replacing the tabs on one and resoldering a tab on the other took care of the issue. MRC has the tabs in stock. If you want to fix it yourself, contact them and they will send the tabs to you. I got three tabs for about fifteen bucks. I only replaced the tab that broke instead of all of them as they suggested. No point in replacing parts that haven't failed yet. They will fail later and you'll have some spares. If you don't press them too hard, which is difficult because they are stiff and don't have the familiar 'click' when they are pressed, then the chances of them failing are greatly reduced.

 

Last edited by Mike D
@Mike D posted:

Remove the boards with the diodes and yellow plastic strips on the left side. Flip it over and check all three copper tabs very carefully where they are soldered to the board. Look for failed solder joints and broken contacts. This is a known issue with these transformers. I have the PP Dual and the PP. Both of mine have had this failure and replacing the tabs on one and resoldering a tab on the other took care of the issue. MRC has the tabs in stock. If you want to fix it yourself, contact them and they will send the tabs to you. I got three tabs for about fifteen bucks. I only replaced the tab that broke instead of all of them as they suggested. No point in replacing parts that haven't failed yet. They will fail later and you'll have some spares. If you don't press them too hard, which is difficult because they are stiff and don't have the familiar 'click' when they are pressed, then the chances of them failing are greatly reduced.

 

I took it off and didn't notice anything wrong. Of course I may not have been looking hard enough. 

Attachments

Images (2)
  • 20200528_210402
  • 20200528_210604

Okay, sorry. You have to remove the yellow plastic bar. I think it has four screws in it. the traces are on the other side of the board. the picture you have is of the bottom of that board. BE CAREFUL when removing the plastic bar. There are three springs in there that keep the tabs in place. It is not bad, but if you aren't used to working on this kind of stuff it can be a PITA.

I purchased one of these to replace my Z4000 which I believe needs the potentiometer replaced. I would like to get that fixed eventually. The right throttle of the MRC seems to have a similar issue as mentioned here. It worked fine at first but after multiple uses it became unreliable. Since I don't run conventional I leave it on full power and just turn it on & off with the rocker switch & power strip. So far so good. 

The left side of my transformer went dead after pushing the directional button, but after sever pushes, it came back to life.  I put a piece of tape over it so I wouldn't push it again until a couple days ago. Oops !

Thanks to you guys and this thread I got the courage to open it up and knew what to look for.       Here are a couple pictures; 

The first thing I noticed was the copper tab catching on the wire, upper right, but it hadn't worn through the insulation, so I bent the wire out of the way. 

DSC04305 [1024x758)

After removing the yellow plastic cover, sure enough the solder joint for the tab had come loose. 

DSC04308 [1024x758)

Now off to Harbor Freight for a soldering gun,  I guess a 25 watt will do the job ? 

Doug

Attachments

Images (2)
  • DSC04305 (1024x758)
  • DSC04308 (1024x758)
@boomer0622 posted:

The left side of my transformer went dead after pushing the directional button, but after sever pushes, it came back to life.  I put a piece of tape over it so I wouldn't push it again until a couple days ago. Oops !

Thanks to you guys and this thread I got the courage to open it up and knew what to look for.       Here are a couple pictures; 

The first thing I noticed was the copper tab catching on the wire, upper right, but it hadn't worn through the insulation, so I bent the wire out of the way. 

DSC04305 [1024x758)

After removing the yellow plastic cover, sure enough the solder joint for the tab had come loose. 

DSC04308 [1024x758)

Now off to Harbor Freight for a soldering gun,  I guess a 25 watt will do the job ? 

Doug

I used an Xtronic soldering station (3020) from Amazon to solder my tab but I also have a weller soldering gun. Once upon a time I had both the iron and gun from HF and threw them both away. They were junk. 

I got it fixed after a couple try's,  with the first attempt I reattached the tab with too much clearance between the tab and the contact and the spring would not hold it down far enough.  So I resolder it and now it works fine. 

Ironman1,  While having the transformer open I noticed a couple set screws that hold the brush arm onto the shaft.  Maybe that's the problem with the handle moving and no voltage increase, the shaft is slipping. 

DSC04311 [1024x768)

Attachments

Images (1)
  • DSC04311 (1024x768)
@Mike D posted:

If it is just a failed solder joint and the metal isn't actually broken, you should be able to reflow the connection and be good to go. That is how I repaired one of mine. The other one had the contact actually broken in two.

Got it off. Looks like the one for the direction key need to be resoldered as it popped off when I took the strip off.

Fixed. Wonder how that tab got unsoldered?

It only took a little less than 2-1/2 years, but I finally got around to taking another look at it.  Broken solder joint on the tab for the direction button.  I had opened it up several years ago, but the broken joint was not really visible - had to move the tab to notice it.

Resoldered it and... success!  The little screws that hold the spring bar in place are a PITA, but thanks to all the info here I was prepared for them.  This was possibly the easiest soldering repair I've ever done.

Thanks to all who contributed to this thread - I couldn't have done it without you.

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×