Skip to main content

Dear Friends,

I have a couple of these 3-rail MTH auto cars with end doors. They made a variety of these, I got elder versions with cast on grab irons oversized ladders and monster stirrups. But I love the rest of the car, it makes a very good and inexpensive representation of a Union Pacific A-50-15 of 1938. The underframe, however, is a mess and a conversion only became an option since I have a 3D printer.

UNADJUSTEDNONRAW_thumb_804c

Here you can see the printed bolster in place. I had to file down the car ends a bit to end up with the coupler in the right hight in relation to the riding hight. The geometry here is essential for a good appearence. But once you got the work done, you can convert easily as many cars of the same type as you wish.

UNADJUSTEDNONRAW_thumb_7ea9

The new truck bolster has a big cone to accomodate the metal underside of the car. Next time I will work on lowering the underbody details somewhat more, they sit too high up there. The car has an odd assembly philosophy. Here's the PLA printed bolster. I work in FUSION 360 (free).

UNADJUSTEDNONRAW_thumb_7ea7

The ladders were really a problem and so I desided to solder new ones. A good exercise since I don't soler a lot.

xO5op+1jQySj%aObRv83Rw_thumb_7e9e

The new ladders look much better, although I made a mistake in placeing them in a different stepping hight. Next time!

IMG_4389

Tamiya grey rattle can primer is what I use all the time on plastic.

UNADJUSTEDNONRAW_thumb_7eab

Followed by some Tamiya brown/red. The color sprays good when I thin it about half with alcohol. These grab irons were left overs from a InterMountain reefer kit, with two of these you end up with enough spare grab irons for an other car.

UNADJUSTEDNONRAW_thumb_7eaf

I did a big mess when I tried to sand away the original MTH factory lettering. The damage was repaired with some putty and a bit of rust. In the end it turned out even better than without. Protocraft decals went on, I enjoy lettering stuff a lot.

UNADJUSTEDNONRAW_thumb_7ff1

I've discovered Tru-Color and Mr. Metal Surfacer for painting steel wheels. Absolutely my favorite color! it layes down super smooth and it does not take on powders, so mooth it is. I think this would be perfect to do decalling on. Will experiment more with it in the future.

UNADJUSTEDNONRAW_thumb_8041

These are InterMountain plastic trucks converted to P:48 with a printed truck bolster. I work on it but the results are promising.

UNADJUSTEDNONRAW_thumb_804b

The weathering might be a bit over done and was carried out with oil washes on super flat varnish. Here I have much to learn. The kind of clear coat extremely affects all weathering effects.

UNADJUSTEDNONRAW_thumb_8049



Would I buy more of these? I've got a total of four and I will convert them but maybe I'd rather save some money and go for a Protocraft brass model that is absolutely 100% super correct. But hey - it was fun and that car certainly is one of my babes now, nursed back to health.

Cheers, Sarah

www.trainkitchen.com

Attachments

Images (11)
  • UNADJUSTEDNONRAW_thumb_804c
  • xO5op+1jQySj%aObRv83Rw_thumb_7e9e
  • IMG_4389
  • UNADJUSTEDNONRAW_thumb_7ea7
  • UNADJUSTEDNONRAW_thumb_7ea9
  • UNADJUSTEDNONRAW_thumb_7eab
  • UNADJUSTEDNONRAW_thumb_7eaf
  • UNADJUSTEDNONRAW_thumb_7ff1
  • UNADJUSTEDNONRAW_thumb_8041
  • UNADJUSTEDNONRAW_thumb_804b
  • UNADJUSTEDNONRAW_thumb_8049
Last edited by Sarah
Original Post

Replies sorted oldest to newest

@Sarah posted:

The weathering might be a bit over done and was carried out with oil washes on super flat varnish. Here I have much to learn. The kind of clear coat extremely affects all weathering effects.

UNADJUSTEDNONRAW_thumb_8049

Actually, I think the weathering looks great, not overdone at  all!  You never cease to amaze!

If you think it's bad, I'd be delighted to take it off your hands!

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×