Skip to main content

Updated 3/15/2020:

I have many irons in the fire this Ides of March. I am exploring some ways to super detail the bridge. Also underway is the WV scenery. That is taking much longer than I anticipated or wish. Visualizing a 3-D topography in a tight space is a challenge. Carrying it off will be even more challenging as it includes accurate placement of abutments, piers, and plaster castings.

The drainage ditch (about 5' long) between the eastern bridge approach tracks and the backdrop is nearly complete. It has received scenery and will soon get water.

More when I know it.  

George

Updated 3/21/2020:

The drainage ditch on the WV side (between the tracks and the backdrop) is done!  Trees, water, vegetation, and some deer were added to it and it has been fastened into place.

I have also constructed several line poles with 6 cross-arms per the photos of the prototype.  These need double sets of cross-arms - in progress.  I spoke to an excellent 2-rail scale O modeler who is an expert on Pennsy line poles.  He's not on line so this was by phone.  I mailed him the photos of the funky 3-pole contraption at the east end of the bridge.  He gave me some advice but he's never seen anything like it.  So it remains a bit of a mystery.

I am also in the process of pulling bus wire pairs under the bridge.  These are for:

  • Bridge - Eastbound
  • Bridge - Westbound
  • Steubenville
  • River Route
  • 12 VDC accessory bus


And finally, work on the scenery behind the stone arch and the WV shore continues.

More when I know it.  

George

Updated 4/10/2020:

Sorry it's been so long since I provided an update. Work continues apace:

  • Scenery work behind the stone arch and the first eastern approach span is done.
  • The stone arch and pier #1 are now permanently installed on the layout. They have been screwed in place.
  • Wiring for accessories near the arch has been installed and tested.
  • I extended the hillside behind the arch a further 6" west into the river. I needed to do this because I found that I couldn't hide my poor backdrop painting without it. Now I can install trees that hide my crappy paint job. :lol:
  • I am in the process of acquiring, assembling, and painting detail pieces for the WV side of the river.

More when I know it.  

George

 

Updated 5/13/2020:

All, significant progress has been made on the layout.  Scenery on the WV side river bank is complete, although the area beneath the stone arch remains.  The river has been poured.  Photos are not currently available, but may become so in the near future.  Work on scenery-related items continues. 

I am exploring additional means of reporting status on Panhandle 2.0.

George

Well George, the progress on your layout is truly impressive. But what really got my attention is the length of this thread!

Thank you, Neal.

This thread, in one form or another (Panhandle 1 or 2), has been on this forum since 2005 and in that time has gathered well over 125,000 views.  I am proud of that and extremely grateful for the following it has attracted.

George

Updated 5/20/2020:

Over the past few weeks, I've finished the scenery on both shorelines (sorry about the lack of photos, but that must continue for reasons that will become apparent later). 

However, I did undertake a cleaning of the bridge (I've been swiffering! :D .  The scarcity of 90% isopropyl alcohol (for track cleaning purposes) is an unintended consequence of the COVID-19 pandemic.  That meant I had to use 50% isopropyl alcohol.  I put that on a swiffer pad, put the pad on the handle, and was able to reach into the bridge to clean it.  Turns out there was a lot of gunk on the track.  After the cleaning, I covered up the track with some butcher paper.  We still have a lot of construction (about 60% of the benchwork) remaining.  There will be much, much more dust and dirt flying around.

Bridge Cleaning 01Bridge Cleaning 02

George

Attachments

Images (2)
  • Bridge Cleaning 01
  • Bridge Cleaning 02

Dave and Mark,

You should have seen the dirt and grease I took off the tracks!  About 4-5 months ago I tried to run an engine across the bridge under command control.  Good thing I was standing by the power button.  The dirty track had negated the signal and the locomotive (that wonderful Decapod) took off like it was shot out of a cannon (18V to the track; full throttle).  

George

Updated 5/23/2020:

While I wait for some parts to be fabricated for me, I have turned my attention to finishing the shelving in the Staging Area of the layout.  This section of the layout is a kind of experiment for me.  Several other modelers I know have an area off the layout for making / breaking down trains;  sometimes this is referred to as a "fiddle yard".  We'll see how this turns out.

Description:

My Staging Area is a 6' x 10' unfinished area at the eastern end of the layout.  It is hidden from the rest of the layout by a divider.  On the layout side of the divider, I have a photograph of the Weirton Steel blast furnaces (circa 2010); these are now gone (torn down in 2018-9).  The Staging Area side has large access holes (not hatches) that permit a person to stand in the middle and reach most of the trains / locomotives.  I am hoping to position a person there during operating sessions.  Features of the Staging Area are:

  • Wall shelving on the back layout wall with a capacity of ~ 40 standard length cars
  • Wall shelving on the back of the divider with a capacity of ~ 45 steel-related (shorter length) cars
  • Storage for at least 6 large locomotives; shifters are stored in yard pockets, by the way.
  • 3 storage / staging tracks (I can keep 3 trains ready to run on them)
  • The reversing track for Weirton Steel blast furnaces.  This is a place to change hoppers, boxcars, ore cars that service Weirton Steel to / from empty / full.  
  • Access to the Staging Area is through 4 holes in the backdrop divider.  I will probably disguise the bottom (southern) two entries as building fronts.  The top two will be disguised by the overpass (Crawford's Crossing).


Here's a view of track plan showing Weirton Steel and the Staging Area.  Items of note:

Staging Area v2

  • The red "E" indicates the eastern side of the layout.
  • The green vertical line is the scenic divider.
  • The light green areas are access hatches. I have to be able to reach into buildings.
  • The two white areas in the Staging Area proper are access holes (no covers).
  • Weirton Steel mills (bottom to top):  Strip Steel, Open Hearth, Blooming Mill are angled at 45 degrees against the scenic divider.  This permits more buildings to be represented in the available (and limited) space.  Otherwise the space would be dominated by only one of these huge structures.
  • The track running parallel to the southern side of the Strip Steel building will have a sign saying "to blast furnaces".  That is effectively my track to the highline of the blast furnaces, supplying them with coal, limestone, and iron ore.  From that track will also come slag cars and hot metal (torpedo) cars.
  • Slag cars (full) will proceed to Standard Slag for dumping.  Empty slag cars will return to the blast furnaces for loading.


The "operator" for this area will be responsible for changing cars to fit the operations described above.

Construction of the space continues.  Early in start of the layout, I built the tables and the shelves against the far eastern wall.  Right now I am working on the shelving against the back of the divider.  Here's a look:

This is the backdrop on the divider.  The Weirton Steel mill buildings will go against it.  The Staging Area is behind it. 
Staging_001_

This is northeast corner of the Staging Area.  To the left is the window with its fan.  I expect to have the fan on during operating sessions to help keep heat down and exhaust any smoke.  To the right are the ends of the Glenn Snyder shelves.
Staging_002_

This is the southeast corner of the Staging Area (the other end of the Glenn Snyder shelving).
Staging_003_

This is northwest corner of the Staging Area.  I have the lowest shelf in place and am working on the one above it.
Staging_004_

Here's the southwest corner of the Staging Area.  Right below the rocket launching car is the spot (approximately) where the blast furnace track will enter.  The exact location is still TBD.
Staging_005_

Here's a look at one of the access holes.  I'm standing in it.  Unfortunately, the whole Staging Area is too cramped to provide a wide angle look at a complete wall.  You can see some of the uninstalled shelving.
Staging_006_

Finally, this is a somewhat better view of the reversing track location.  The 2' level approximates the position of the track.
Staging_007_

More when I know it.  

George

Attachments

Images (8)
  • Staging_001_
  • Staging_002_
  • Staging_003_
  • Staging_004_
  • Staging_005_
  • Staging_006_
  • Staging_007_
  • Staging Area v2

George, the blast furnace backdrop looks great as do the shelves.  You may have answered this before, but how high is the benchwork?  I was wondering how you will get to the access holes, duck, sit down and scoot around,...  I have a few aluminum shelves similar to Glen Snider shelves that I can't figure out where to hang them.  No wall space to speak of.  

Thanks Mark.  The height of the bench work is 50".  To get to the access holes, I am planning on using a roll-around stool.  Near the access holes in the Staging Area, I plan to put a 2-step ladder.  That will allow me to get up on the bench work (if need be) to open or close the window.  The exhaust fan is activated by the wall switch.

Rolling Stool 

George

Attachments

Images (1)
  • Rolling Stool

Updated 5/24/2020:

I completed installation of the remaining Glenn Snyder display shelves in the Staging Area.

Staging_008_

Staging_009_

That's all for the Staging Area for the near future.  The immediate areas of focus are:

  1. Finish super-detailing the bridge
  2. Permanently place the bridge back onto its piers and abutments
  3. Install all the approach track and connect track feeders to the bridge's electrical buses (eastbound, westbound)
  4. Complete the scenery areas near the backwater, between Pier 1 and the Stone Arch, and at the front of the Eastern Approach.

 

More when I know it.  

George

Attachments

Images (2)
  • Staging_008_
  • Staging_009_

Updated 5/26/2020:

I have a divider between the layout and the Staging Area.  When I originally installed the backdrop up on the divider, my intention was to extend it all the way to the ceiling.  I prepared the area to receive a backdrop extension.  All that got pushed to the back burner as I tried to get the bridge area ready for the NMRA Mid-Central Regional Convention at the end of May (which was, of course, cancelled due to the COVID-19 pandemic). 

So now, with some time on my hands awaiting parts, I started looking at this again.  I was about to pull out some 10' sections of blue sky backdrop (from the original order to RailroadBackdrops.com), when my better half decided to inspect the area.  She had a brilliant idea - just paint the area above the Weirton Steel backdrop the color of the wall.  It would match the rest of the area and there would be no reason to do this extra work.  So that's what I did!


Staging_011_

It will get two coats of paint and then I'll pull the protective masking off and declare victory!

George

Attachments

Images (1)
  • Staging_011_

Updated 6/15/2020:

While work continues on the scenery in the Ohio River valley and on the bridge, some electrical work has also been conducted ("nyuk, nyuk, nyuk").

Awhile ago, I acquired a second 12V DC power supply.  Today I re-arranged some of the other supplies and mounted them all vertically so as to get more air flowing around them.  I also decided that I will move 3VDC "wall warts" to remote power strips located at the ends of the layout.  These will power street lights (my lighted telephone poles) and traffic signals.  Here's the new transformer cart diagram.  Changes were made primarily to the lower level of the cart.

20200615 Transformer Cart

Here's a shot of the work (in progress).  Left to right - the new 12VDC supply, the existing 12VDC supply, and the 5VDC supply.  The barrel connector to the extreme left is the 3VDC supply which is yet to be moved.

IMG_3868

More when I know it.  

George

Attachments

Images (2)
  • 20200615 Transformer Cart
  • IMG_3868
Last edited by G3750

Updated 7/10/2020:

Physical work on the layout has ground to a halt while we try to help our children move to a new apartment.  However, my mind has been active.

I have been contemplating some changes to the track work around the Steubenville PRR station.  Market Street will be moved about 6" left (west) as indicated by the black arrows.  The green arrows indicate proposed new track, including a passenger siding capable of holding 3-4 passenger cars or head-end cars (baggage, express mail, reefers) and an engine pocket.  It might be possible to hold a switcher and a reefer car there (to work with the Armour Packing siding).  I'm thinking 6th Street might be extended to intersect with Market.

77x2d variation

The jury is still out on making this change, but it looks tempting.  Plenty of more pressing work, but...

More when I know it.  

George

Attachments

Images (1)
  • 77x2d variation

Updated 7/10/2020 PM:

After some reworking, I am leaning towards changes that would:

  • Move Market Street 6" to the west (left)
  • Move the 4th Street overpass about 12" to the east
  • Extend the passenger siding to 72", enough for four 18" passenger cars, i.e. the entire "Spirit of St. Louis".
  • Lengthen the engine pocket to 34", perhaps enough for both a switcher and a reefer

Here's a look at the revised area.

77x4 variation

More when I know it.  

George

Attachments

Images (1)
  • 77x4 variation

Updated 7/14/2020:

Thanks Mark, I'm trying.  

As the saying goes, "When the map and the terrain differ, believe the terrain."  I have put things on paper, thought they were OK and then watched them fail.  I like RR-Track and it is a decent planning tool, but you've got to be careful when you consider 3-D aspects (e.g. elevation of hills).  That's important in this situation, as the retaining wall behind the passenger siding is where the scenery will slope up to the backdrop.  To get a practical and workable slope, you've got to leave a bit more room than you think is necessary.  Particularly on Panhandle 1, I recall planning an elevated track and then having to back off because it was impractical.  An inch of clearance takes on the appearance (with zooming in / out) of 6".  Sometimes, I've convinced myself that an impossible clearance is going to work.  

The newly modified area around the station is particularly tight - close tolerances.  That's why I have some track and 18" cars out on the bench work playing with the physical fit of the components.  The leftmost track (nearest the backdrop) holds the K-Line 18" streamlined observation car from the Spirit of St. Louis 4-car set.  To the right, on the right hand side of the turnout, are two K-Line 18" heavyweight passenger cars (PRR Broadway Limited).   These sit on the mainline.  The track is roughly in the correct position.  The two curved sections of track (O80, O72) flanking the mainline are not part of the layout;  they're just laying there.  The green styrofoam beyond the passenger cars is part of the hillside and will be extended toward the viewer, exact dimensions TBD.

IMG_3949

More when I know it.  

George

Attachments

Images (1)
  • IMG_3949

Updated 7/21/2020:

  • Placed my orders with Ross Custom Switches for the 2 new switches discussed above.
  • Acquired bus logos (P&W Bus Company) for the two Corgi GM old-style vehicles currently being painted in the correct color scheme.  These will be turned into water slide decals.
  • Bus Logo - RightSide.jpg
  • As part of the planned re-alignment of Market & 4th Streets and the additional tracks at the station, I'm planning an experiment with my MTH PRR signal bridge, a DZ-2500 equipped turnout, and a DZ-1008 relay.  I want to see if I can possibly use the switch to activate the signal head on the bridge.  It's one of the cheaper alternatives, if it works.
  • I am still working on details for the bridge piers and bridge.
  • And I bought some brass rods for use in hanging a conduit on part of the bridge.

Lots of motion, not nearly enough forward progress.  Or so it seems.   
 
More when I know it.  
George

Looks good George. I like some of the old cars, buses and trucks you can find out there in the world. Just takes a bit of looking. A few years back I bought a trailer and truck from Brooklyn Models(in the UK IIRC), they are really nice, but expensive. I wanted to keep in line with being around 1949, and I think the two were supposed to be 1948. Some other stuff I have bought are older in the mid to late 30's or early 40's, but it wasn't uncommon to see such older vehicles back then in certain areas of the country.

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×