Skip to main content

Yes, these were original 5V with boards in the engine.  That is usually the harder replacement with a non original board.

 

If I go that route RJR, I feed the engine markers off the headlight circuit with a limiting resistor.  Works fine and they don't come on until engine is started up.

 

While there looks to be plenty of room at the base and length, you start running out of real estate at the top.  Narrows and looses height.  Plus you are trying to match up to existing threaded holes.  G

Originally Posted by RJR:

GGG, so you add the 2 markers to the headlight circuit.  What size resiator do you use?  I assume the headlight xircuit can handle the 2 marker bulbs in the PS2 upgrade kit?

I use a 150 ohm resistor and convert the markers to series if they are not already series.  150 is what MTH used on PS-1 6V CV boards.  All PS-2 markers are series.

Works fine.  G

Some were sent to the tech guys who requested them.  My best information is they will be ready for July.  The public can buy them then also.  MTH is still keeping the PS3 2 board to replace 5 and 3 volt boards to tech only.  I will not buy and sell these to people unless I am the person who does the installation.  I still have many 5 volt boards running around the layout.  

 

The kit is the same except no battery or wiring that goes with it.  You can do one in your sleep John.  

the last i heard from mth i had ordered 2 ps2 3 volt steam kits but they did not get as many as they thought they would , so i was called after i placed the original order and they said they would mail me a ps 3 kit in it's place since ps 2 3 volt kits where no longer available. Midge told me that the ps3 kits would be shipped in June 2015!

Alan

Originally Posted by gunrunnerjohn:

Since they're using the "replacement" board, I figured the kits would be very similar.  I've used some of the PS/32 boards for 5V replacements, but I still have a few spare 3V boards that I can use as well.

 

I wonder what is holding up the diesel upgrade, maybe it's the extra stuff like pantographs?

 

Diesel harness are the hold up.  G

Here is a DASH-9 Upgrade.  I thought some one stated this did not fit because of body width.  It is very tight and I had to do some precision measurements before attaching the bracket.  Tolerances where about 1mm. It had to be centered along width, but also fore and aft because of the tabs on the body.  You could trim these off as an alternative.

 

Wires must run from front or rear.  Can't have wires coming up the side of the board.

 

G

Attachments

Images (2)
  • IMG_0548
  • IMG_0549
Originally Posted by Norton:

Nicely done again George. Its obvious you are a perfectionist. The factory jobs are not as well done.

 

Pete

Thats because George can take the time to do it right. The Chinese just slap it together, chop-chop-done-next, since its probably pay by the piece work.  More engines/cars is more Yaun in the pocket.

Very nice work!
 
Need to upgrade my DD40AX  
 
Originally Posted by GGG:

Here is a DASH-9 Upgrade.  I thought some one stated this did not fit because of body width.  It is very tight and I had to do some precision measurements before attaching the bracket.  Tolerances where about 1mm. It had to be centered along width, but also fore and aft because of the tabs on the body.  You could trim these off as an alternative.

 

Wires must run from front or rear.  Can't have wires coming up the side of the board.

 

G

 

Add Reply

Post
The DCS Forum is sponsored by

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×