Skip to main content

Replies sorted oldest to newest

George,

If you are indeed referring to the blue XPS foam board by Dow, then Original Gorilla Glue will work wonderfully.  I worked extensively with Owens Corning pink XPS (different brand/color, same stuff) to build my Christmas layout this year.  I can tell you with 100% certainty that Gorilla Glue will bond the foam.  Here is a construction picture from last month:

IMG_6488

Attachments

Images (1)
  • IMG_6488
Last edited by MikeH

Me too. Loctite's Power Grab works also. Just make sure that you read on the label that it's "Foam Safe". Anything with strong solvent will melt foam. They make lower temp hot glue guns that extrude foam safe hot glues. If you're gluing up large surfaces though the glue will chill below liquid before the pieces are in place. For large surface I'd go with structural adhesives.

I have a post from yesterday about a box I converted for storing a Sharknose ABA. When I was gluing the foam dividers in the box I used two glues.  Elmers pro wood glue where I glued the foam to the cardboard and Gorilla glue for foam on foam.The Gorilla glue would have worked for all the gluing however it is much more expensive than the wood glue and I would have had to buy a new bottle.  The Elmers wood glue will work for foam on foam however it takes a very long time to cure. When gluing the foam to the cardboard the cardboard will facilitate drawing the water out of the glue however this does not happen with foam on foam and a sound joint can take a couple of days to cure if it is broad.  The Gorilla glue actually cures faster in the presents of a little water vapor much like CA.          j

Attachments

Images (2)
  • 103_7709
  • 105_7810

5EBC401D-A595-4251-B8F2-E5843992854143BCF36C-DD84-4C78-8F87-A30CE8B4E144Also using expanding foam from a spray can works great if you have all your pieces precut and ready.

  Home Depot and Lowes should have it

Much cheaper I think than the other glues for bulk scenery work for me

  I built most of this mountain so far, using spray foam as adhesive.

 Great for un even joints etc with the expand factor

  Here are some pics

Al

 

Attachments

Images (2)
  • 5EBC401D-A595-4251-B8F2-E58439928541
  • 43BCF36C-DD84-4C78-8F87-A30CE8B4E144
lashup50 posted:

"I think back in the day I used Elmer's White and didn't have a problem adhering the styro to plywood, if that's what you're trying to do."

I'm referring here to the pink foamboard insulation, not the white styrofoam. 

Gorilla Glue and white glue and yellow wood glue will all adhere well to both construction foam and styrofoam.  Both these foams are made by mixing styrene monomer and a foaming agent. Construction foams have more styrene  per cubic inch and less foaming agent thus are denser. Chemically they are nearly identical to the plastic in model kits though the foaming agent may leave behind it's traces.  The problem with using White glue and yellow wood glue is the water in them must have a path to escape wood and cardboard will supply an adequate path for the water to escape. The problem with Polyvinyl acetate "white glue" is it is not very resistant to moisture.  Yellow wood glue "Aliphatic resin" is more resistant to water once cured.  If I am gluing any foam to cardboard or wood I will use yellow wood glue instead of white glue.  When gluing foam to foam any water in the glue will have a difficult time escaping and the joint will take a long time to cure. This is when I switch to Gorilla glue "Polyurethane glue" in fact a little water vapor will facilitate the cure. Huff your breath on the mating surfaces just before joining.  This stuff will foam up and adequate means of clamping are called for. It is great for filling gaps. Good article on wood glues though much applies to gluing in general.           j

https://en.wikipedia.org/wiki/Wood_glue

Trainman2001 posted:

Me too. Loctite's Power Grab works also. Just make sure that you read on the label that it's "Foam Safe". Anything with strong solvent will melt foam. They make lower temp hot glue guns that extrude foam safe hot glues. If you're gluing up large surfaces though the glue will chill below liquid before the pieces are in place. For large surface I'd go with structural adhesives.

I too like Loctite Power Grab.  An additional benefit is that it's available in a resealable tube, in case you only need a small amount - it will last longer than trying to keep a tube that goes into a caulking gun.  I'm sure that other adhesives are available in similar packaging, but I've found Power Grab to be a good value.

I am with Al! Expanding foam or  “great stuff” works well. It goes a long way and fills gaps for quick sloppy joints.  Temporarily Hold together with clamps, weights or temp nails. The foam expands if it can, but low  expansion foam I available as well.

Just noticed I was working on this mountain exactly 4 years ago.D23EA6DD-9AB5-481B-8936-165EF2881574

13820789-A598-4EAD-8B88-21FE8E1E7AD4

Attachments

Images (2)
  • D23EA6DD-9AB5-481B-8936-165EF2881574
  • 13820789-A598-4EAD-8B88-21FE8E1E7AD4
Last edited by wmcwood
milwrd posted:

I had to try it myself because I couldn't believe it, but Glidden Gripper works great. Not only for foam to foam but I also used it to adhere foam to my plywood deck. Here is a good video on the subject from back in 2012. I know there's some newer adhesives on the market that work well too.

https://www.youtube.com/watch?v=rnOegaOKu38

Looks like a more than adequate replacement for Gorilla glue and very likely a good bit cheaper. I seldom use all the Gorilla glue in the bottle once you reach a point where you cannot squeeze any more air out of the bottle your leaving water vapor along with the remaining air and the glue left will soon cure in the bottle. I wonder if the Glidden Gripper is anything like ceramic tile mastic ?  I have used it on occasion to glue foam and it works fine though it cures a little slower than Gorilla glue. One positive aspect of the Glidden Gripper and ceramic tile mastic is they don't foam up. Probably don't fill gaps as well though.  A small aside on Gorilla Glue and Great Stuff foam. Basically the same substance with a great deal more foaming agent in the Great Stuff. I don't think anyone has mentioned Epoxy yet, or I missed it.  I have often glued Styrofoam with epoxy, it works fine. In fact most of the folks building home built aircraft use epoxy to glue Styrofoam.  This could be yesterdays news as I have not run in the circle in a number of years and I can see Gorilla Glue working just as well as epoxy in many if not most instances.      j

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×