Skip to main content

Does anyone know whether the 262 was designed to require larger than O31 curves?   The engine was my father's in the early 1930s, and is now mostly restored, but we cannot get it to run on O31.  It works well on O42, but I am for now limited to the tighter turns.  

Many thanks,

Doug

Original Post

Replies sorted oldest to newest

The problem may be inordinately worn or un-level track, or an out-of-gauge pilot truck.
All prewar and postwar 0-gauge Lionel were intended to run on 0-31except the 700E/763 Hudson, the 701 switcher and the scale 700 series freight cars as well as the essentially identical 752 M10000 set (752/3/4), the 250E Hiawatha set (782/3/4) or the (792/3/4) Rail Chief passenger cars.

Last edited by Überstationmeister

That's great to know!  

The track is ok - none of my other engines have problems - and I think the pilot is properly gauged.  What about the drivers?  When I put this beauty on the tracks, there is almost no lateral play - which (i)  I guess to be necessary for navigating the turns, and (ii) is present in all of my other steamers.  The play in the rear driver is about half the width of the driving gear, but there is essentially none for the front pair.   The symptom is that the front drivers climb the rails (Lionel tubular) and then derail upon entering a curve.   I am proceeding cautiously here (engine with some serious sentimental value), but does it make sense to try to push the front drivers a bit further apart?  Am I correct in thinking that the lateral play is necessary?  And if so, how much should there be?

Many thanks,



Doug

That's great to know!  

The track is ok - none of my other engines have problems - and I think the pilot is properly gauged.  What about the drivers?  When I put this beauty on the tracks, there is almost no lateral play - which (i)  I guess to be necessary for navigating the turns, and (ii) is present in all of my other steamers.  The play in the rear driver is about half the width of the driving gear, but there is essentially none for the front pair.   The symptom is that the front drivers climb the rails (Lionel tubular) and then derail upon entering a curve.   I am proceeding cautiously here (engine with some serious sentimental value), but does it make sense to try to push the front drivers a bit further apart?  Am I correct in thinking that the lateral play is necessary?  And if so, how much should there be?

Many thanks,



Doug



It's more likely the opposite is required.  The drivers being mounted too far apart are causing it to climb as the radius of the curve is tighter than the space required by physics to make the curve without binding.  This problem occurs quite frequently if a locomotive is being re-wheeled by someone who is lacking skill.  It needs to be checked on curved track before returning it to the customer.

If they are mounted too close together, the loco will "hunt" or bob back and forth sloppily as it runs down the track.  You would see it more on long straight sections.

So the solution "could be" the drive wheels need to be pressed on closer together.  We could be talking about mm's here to make it right.  If your wheels are original to the piece, they could be swollen and expanding due to die cast failure.  The nickel tyres or rims maintain shape, often causing the die cast wheel to bow outwards ever so slightly as it "grows" or expands.  You may not even realize your wheels are doing this, as it could be such a minor amount that it doesn't become noticeable until you have operating issues.

Hope this makes sense.

Agree with Ives1122. The wheels are probably swollen. There should be a fair amount of lateral play on a straight section so when it gets to 031 curves it should run freely. The inside of the curve is especially tight. If you turn the loco around it may run better but doesn't really fix the problem. If you think the pilot is causing problems, take it off and then run it. With the loco upside down turn the wheels by hand and watch the travel in relation to the frame. It should be even as the wheels turn. If one or more wheels wobble it should be easy to spot the bad one(s). Also watch the gear mesh in relation to the main gear. Hope it helps.

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×