Skip to main content

Replies sorted oldest to newest

Gunrunerjohn...so we can add pickups ourselves ! That's great. Perhaps a stretch of my talents, but possible.

I had read in the forum where electric pickups on the tenders were recommended.

Looking at the new models from Lionel, I see very few with them on the tenders. Even some Locomotives with close pickups on the motors. It seems confusing.

I was also looking at the Lionel LC 2.0 Berkshires. None of the tenders have pickups.

Thanks for sharing your knowledge.

@KKNAPPER posted:

Gunrunerjohn...so we can add pickups ourselves ! That's great. Perhaps a stretch of my talents, but possible.

It's just a little mechanical work, and running a single wire from the power to the pickup.   For many locomotives, the power is already in the tender for sound and/or drive electronics, if it's not, I just use a one-wire tether to bring it over.

@KKNAPPER posted:
Looking at the new models from Lionel, I see very few with them on the tenders. Even some Locomotives with close pickups on the motors. It seems confusing.

I was also looking at the Lionel LC 2.0 Berkshires. None of the tenders have pickups.

All of the Legacy models from Lionel have tender pickups, but most of them also have IR drawbars, so the rollers aren't actually connected to the locomotive rollers.  For those I add that single wire tether I talked about.

The LC stuff is different, and they're all over the map on those.

@Windy City posted:

GRJ where can I purchase the pickup and insulated plate shown in your photo?

The pickup is the MTH BD-0000042, the plate I make from 1/16" fiberglass sheet.

Attachments

Images (1)
  • mceclip0

Thanks again gunrunnerjohn.

I understand the philosophy for having pickups now, I understand the science behind them , I know what needs to be done and what parts to use.

Now I'm wondering how I do it?

I have done some research and scanned the forum.

Here is what I believe, I may have learned:

I will be soldering one end of the wire to the pickup ( or both pickups ) on the Tender.

The other end of the wire to the connection point on the motor, where the wire from pickup on the Locomotive is attached .

Connecting both wires with the mechanical pins and sockets.

This seems logical to me, but , I have my doubts on my conclusion.

I feel that after all of these requests for advice, you may request I hire you on a retainer .

I do sincerely appreciate your help.

@KKNAPPER posted:
Here is what I believe, I may have learned:

I will be soldering one end of the wire to the pickup ( or both pickups ) on the Tender.

The other end of the wire to the connection point on the motor, where the wire from pickup on the Locomotive is attached .

Connecting both wires with the mechanical pins and sockets.

NOOOOO!

The other end of the tether in the locomotive does NOT connect to the motor!  It connects to the track pickup wire in the locomotive.

@KKNAPPER posted:

Thanks again bmoran4...I will continue to search through the forum.

I guess I should make sure any Locomotive I buy ( 0-6-0 , 2-8-4 or 4-8-4) has pickups on the tenders .

Most of pickups are very close on the Locomotives themselves.

I only have seen a couple 4-8-4 , where they are spaced out like a regular.

Thanks again .

You might consider just running your new loco first for a while to see if you even have an issue that would require additional pickup rollers. 

Have Fun!

Ron

Improve short locomotive wiring in 7 steps

By Peter H. Riddle | March 29, 2021

Stuttering through switches can be fixed with this one-night project.

(I'm adding this story I found to help anyone else who is experiencing a problem with short foot print pickups...kk)

I hope it helps.

Some of today’s short-wheelbase locomotives have issues with the prototypical switches and narrow-angle crossings that make an O gauge railroad look realistic. Here’s a quick fix that will allow any locomotive­ ­- even this economical Bethlehem Steel saddle tanker from Lionel – to perform reliably over the troublesome trackwork.



A short O gauge 0-6-0t steam switcher approaches a pair of track turnouts
The underside of Lionel 0-6-0t and GP9 locomotives showing the spacing of the pickup rollers.
Making a wire harness by crimping male and female solderless connectors each to a length of 24-gauge stranded wire.
Soldering wire with female connector to metal contact for pickup roller on caboose truck that has been unscrewed from body.
Truck reattached to caboose body with wired female connector affixed to the underside with a piece of double-sided tape in a position that does not show when caboose is on track.
Wiring with male solderless connector is connected at the other end to the locomotive pickup screw with a spade connector. Wire is held to the locomotive body with a piece of double-sided tape
The underside of the locomotive and caboose coupled together with connected male and female solderless connectors.
Locomotive and caboose upright on track approaching track switch.
A short O gauge 0-6-0t steam switcher approaches a pair of track turnouts
The underside of Lionel 0-6-0t and GP9 locomotives showing the spacing of the pickup rollers.
Making a wire harness by crimping male and female solderless connectors each to a length of 24-gauge stranded wire.
Soldering wire with female connector to metal contact for pickup roller on caboose truck that has been unscrewed from body.
Truck reattached to caboose body with wired female connector affixed to the underside with a piece of double-sided tape in a position that does not show when caboose is on track.
Wiring with male solderless connector is connected at the other end to the locomotive pickup screw with a spade connector. Wire is held to the locomotive body with a piece of double-sided tape
The underside of the locomotive and caboose coupled together with connected male and female solderless connectors.
Locomotive and caboose upright on track approaching track switch.

The bane of O gauge operators everywhere is having a small locomotive with closely spaced power pickup rollers – operating through long switches that stop ’em dead in their tracks. Here’ a simple, step-by-step process to keep the juice flowing! Photo by Peter Riddle

Supply list

22- or 24-gauge wire

Male and female solderless connectors

Crimp-on spade connector

Screwdriver

Soldering iron and solder

Two-sided tape

Wire cutter/crimper

Last edited by KKNAPPER

Add Reply

Post
This forum is sponsored by Lionel, LLC

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×