Tie coloring....frustrating.....

Chris,

I know you have seen this before, but you might want to take another look:

http://ogaugerr.infopop.cc/eve...1048701/m/4232911617

You might want to try some of the materials/techniques mentioned there and maybe dig up a copy of the reference Matt mentions: 2008 Modelers' Annual from Westlake Publishing.

As for the images you have posted, there's certainly nothing wrong with what you have done. How old do you want the ties to look and is it a main or branch line? I would think that would decide the effect you would be shooting for.

I don't think it's an exact science, and I wouldn't get too excited until it is ballasted and you have the total look. You might want to "tier" down the look of your track with the main line/lines looking the best maintained and the low usage trackage having the least maintained look.

Ultimately you only have to satisfy one person!

Cheers,
Simon

the ties look great! the tie plates could get a dusting of rust color

Chris...you can go gray haired over this matter, but once you ballast and develope scenery around it, the precise coloring of the ties will become a minor issue. You can always selectively weather individual ties to add an element of age and detail...that would be appropriate later on in the process.

Your making nice progress Chris whatever you decide to do about the coloring.

Bob

Thanks for the responses guys. Simon it is the main line and I am going for what you see in these photos which is a darker oily greased up look. The ties not being terribly old, but heavily used. There about 10 ties I am experimenting on and in my photo I have used some ebony and gray stains as well as some thinned burnt umber pigment.

http://www.flyerguide.net/view...hp?id=283770&nseq=14
http://www.flyerguide.net/view...hp?id=283771&nseq=13
http://www.flyerguide.net/view...php?id=294609&nseq=9
http://www.flyerguide.net/view...php?id=294609&nseq=9

Chris thank you, I am going to be adding some more coloring to the plates and rails. I want to also have them bleed a little into the ties.

Chris,
I see a can of Rustoleum Camoflage paint in the background.
This is what I do: After gluing the ties and sanding them, I stain with Minwax Dark Walnut, then lay my rail and wire, and finally, I spray the track with the Rustoleum Camoflage Dark Brown. The use of the stain helps to minimize the amount of paint that is needed. Without staining, I used a lot of paint to cover the unstained ties. The paint is dead flat and gives a nice uniform appearance to the ties and rail. Speaking of "uniform" appearance, I read or saw on a video a UP track inspector say that lack of uniformity was a clue that something was wrong or could go wrong in the near future. After hearing his remarks, I don't consider uniformity of color a bad thing. The ties in your pictures of the N&W mainlines show a uniform color.
Hope this helps.
Regards,
Ed

Joe G. recommends artist acrylic craft paint called Neutral Grey, which has that brownish tint you're looking for.
I use Rustoleum grey and black primer, paint the track and ties, then go back over the ties to highlight and weather them. Good 'nuff for me.

In looking at color shots then and now I find a great difference between the appearance of track in the late steam era and today. Track in the pre-roller bearing era often had gray/black crud on the rail, while today's rail seems to just look "rusty" if not near flange lubricaton device. I suspect this was due to slow lubrication run out from solid bearing journal boxes, mixed in with cinders from passing steam locomotives. As a side note I've observed a huge difference in the color of wheel faces between roller bearing and non-rollller bearing trucks.

If you haven't already done so, before settling on a weathered look for your track, study available color photos of the railroad you wish to model taken in the relevant era. I model PRR in 1952 and have had to totally rethink the weathering I did on earlier railroads. My favorite site for late steam era color photos is John Dziobko. John's photos have been published in PRRT&HS and Morning Sun books - but I really look forward to visiting his website as new shots are added every few weeks.

Ed Rappe

Hi Ed...since I'm a 1952 PRR enthusiast as well, I have ask what your color choice has come out to be for rail/wheel? I have been using a common roof brown myself.

Thanks

Bob

Thanks for the responses everyone.

Ed K. I did use the camo brown on the tie plates and rails for a "base" color, and I am going to go back with other rust colors and chalks to blend them and to vary the color along the rails. Thank you for the help I appreciate it.

Thanks John I will look into that....sounds good.

Ed R. I am modeling the steam era...primarely the N&W. I have looked at gobbs of photos as well and have come to the same conclusion, the track was much darker in the steam days. As you said between the journal boxes leaking and grease flying off the rods not to mention all that brake dust since there wasn't any dynamic breaking to be had yet. Thank you for the link I am going to go and take look see.

Thank you very much for all the help guys I do appreciate it.

Bob - I haven't started to weather the track yet as I'm holding off until after the branch is fully operational. Last month I laid quite a bit of track to connect the branch with the main. The only trackwork remaining to build is the Oceola Mills yard - about 12 turnouts.

At this point all I know is I won't be using straight Floquil rail brown as on my old railroad. I think Chris's base color looks quite good. I'll probably try playing with a mix of grimy black and rail brown/rust on the sides of the rails. In addition to 2400' of track to weather - I have more wheel sets to re-weather than I'd care to count! Perhaps if internet photos were around in the 1980's I'd have done better the first time around.

Chris - please continue to share - we'll all benifit.

Ed Rappe

I am from the Chicagoland area and I see all kinds of ties. the ones on the mainlines e i ns,csx ihb,csssb, on their mains are nearly all black.the only difference is on the sidings and yards where they are more of a brownish color.Yours look fine. I find no complaints about them. Booyak.

quote:

Originally posted by anzani racer:
why is it all the hand laid track i see is raw wood. then painted after the rail is laid? you could get the color stain that you like and soak the ties before they get placed.
. ...rob

Ive done both methods, and hands down I like to stain on the already glued down ties for a few reasons:
I can adjust the tie color for the service it will placed in, Soaking ties is messy, and then you have to strain them and let them dry..also messing and time consuming. Plus I dont stain a bunch of ties that I wont end up using. My ties are mostly homemade and I probably throw away one outta 15. But I can make them for .0032 cents a piece so they are cheap.

Chris,
The ties look very nice. I thought they were real at first. The rail and tie plates need more gray (don't tint toward the red any more). Most rail that I ride on, the ties, rail & plates tend to blend/complement each other.

Good evening all, I really love all the input and advise you guys are the best.

Anzani racer thanks for the link, very informative. I actually am using a ebony stain in areas on the ties for shading and such.

Big Jim thank you very much, you hit the nail on the head. As silly as it is I have been looking at the rail and plates all day and wondering what color will do what I am seeing in my mind and in photo's and the gray's will do it perfectly.

Ed R. All I can say is that regarding that link you posted....wow. He has some great photo's there....color also. Which really was helpful. Thank you again.

Ok here is my latest efforts, the tie's now appear lighter in these photo's and are in fact much darker in person...gotta tone down the lights a bit.

Another world class layout is underway!

Nice work, keep us up to date!

quote:

Originally posted by Erik C Lindgren:
Another world class layout is underway!

Nice work, keep us up to date!

Yes, Looks good Chris!

Thank you so much guys, I will keep the pic's coming.

Chris,

all that looks really good. I don't think you really need to change anything either as there is so much natural deviation anyway. And as others have stated the track work's appearance will get even better as you complete ballasting, weathering, etc.

John

Tie color is hard to get wrong. The one thing I will say about your project is that anyone who is this picky about getting it right is ultimately going to end up with some spectacular track work!