Skip to main content

I recently had an old steam loco upgraded with ERR control and railsounds.  Got it home and tried to assign an engine number other than 1 to it, no joy.  No sequence of events will allow me to program this loco with an different engine number, but worse yet, the front headlight turned off at some point in this attempt and I cannot figure out how to “re-light” it.  The biggest issue, I now have two steam locomotives stuck on engine id 1.  The first time this happened I assumed it was a bad program/run switch on the first locomotive but now I’m questioning that.  So far I have three locomotives, two steamers that will not allow me to assign a new engine id, and one Kline diesel with TMCC that does allow me to assign a new id to it.  This is a legacy controller, version 1.5.2 of the software.  Am I missing something here or do I really have two steam locomotives, one recently upgraded, that just won’t accept a program?

Original Post

Replies sorted oldest to newest

I don't know which ERR board kit my repair shop used, and unfortunately he'll be unavailable to answer that question until Wednesday.  The other Loco that won't program is a Lionel B&O EM-1 6-28051.  To program I've:

1.   Powered off the track

2.  Moved the Run switch to Program

3.  Placed the loco back onto the track and powered up the track

4.  On the Legacy Cab, press ENG, 76, SET.  (Not getting any response from either loco after pressing SET).

5.  Power off, remove the loco, flip the switch back to Run, return to the track and power on

6.  Pressing ENG 76 on the legacy cab, no response from the locomotive.  Press ENG 1 on the legacy cab, responds immediately.

On my EM-1, I can turn the front light off using the AUX 1 button on the CAB, however for the Mohawk with the ERR board, I do not know how to turn the headlight on and off, it's definitely not responding to the AUX1 button.  My repair guy recommended trying a reset by doing this:  In program mode, Press Engine, Engine number (in my case 1), SET, AUX1 and then #4.  However, on my legacy cab, I press Engine, 1, set, AUX1 and the keypad does not change to numerical mode.

First, it doesn’t seem like the program switch is connected properly...I wonder, if you set the switch to program and power up the track, before doing anything else, does the engine then run with the ENG 1 command? That would suggest that the program switch is not doing anything.

On the reset, you won’t get the numbers back, but just count to 4 on the pads and press that button...the button that would have shown the number 4. That works fine.

"On my EM-1, I can turn the front light off using the AUX 1 button on the CAB, however for the Mohawk with the ERR board, I do not know how to turn the headlight on and off, it's definitely not responding to the AUX1 button."

For ERR boards, the AUX2 button toggles lights on and off.

Finally had a chance to take the ERR loco back to the shop.  Turns out that the program/run switch wasn't wired.  Once he made those connections, that locomotive is working like a champ.  Interestingly it turns out the marker lights on the tender aren't compatible with the ERR board and that's why they aren't lit, leaving the headlight as the last mystery.  It looks like the headlight happened to burn out amidst all this troubleshooting, waiting for that replacement bulb now.  It's a bummer about the red marker lights on the tender, I wonder if they can be hardwired to a power pickup from the track somehow and bypass the ERR board?

Actually, unless the red markers are VERY unusual bulbs, they can be made to work with the ERR stuff, I do it all the time.  They're likely LED's on the tender, a resistor and diode with the proper wiring will light them from the headlight circuit.  Since the front headlight remains on all the time on steam, I wire them to that output, that allows me to have command control of the markers to turn them off with the lights.

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×