Skip to main content

I just purchased a 2010 Visionline Challenger 6-11210 3967 used from eBay and I removed the shell to service the smoke units and to fix the number boards and marker lights that didn't work but now when I'm putting the shell back on its shorting itself out at the cab of the shell. If I lift the cab of the shell just a 1/16 of an inch it's fine but if I put the screws in it shorts out. I've checked and there are no pinched wires anywhere. The guy I bought this from sent it to Brasseur's Trains to replace the wireless tether on the engine and they didn't check it before sending it back to him. Does anyone have any ideas why it would be shorting out? The engine runs fine if I leave the screws under the cab out. I really don't want to run it this way without all the screws in place. Any idea's what this could be. Thanks  Gary
Original Post

Replies sorted oldest to newest

i would take pictures with engine apart and post them here and the experts here will give you there experienced opinions ! are you sure you seated the module pins on the mother board correctly to keep them from shorting ! if you keep powering up the engine up you WILL BURN  UP THE BOARDS AND COULD BE A VERY EXPENSIVE REPAIR ! JUST ASK ! ALEX M. WHO SPECIALIZES in Lionel engine repair !

Alex M | O Gauge Railroading On Line Forum (ogaugerr.com)

An ounce of preventtion is worth a pound of CURE !

Alan

Last edited by Alan Mancus
@Gary Marsh posted:

Thanks Alan and gunrunnerjohn for you input on this. I tried sending Alex a message thru his email address listed on his profile but it was returned as undeliverable. Does anyone happen to have his email address so I can contact him? Thanks Gary

His profile has a good email address, so it was something else.  I sent him email to that address regularly, AAMOF, just about five minutes ago!

Like I said, it's busy in there, ten pounds of xxx in a five pound bag!

When I run up against something like this, I lay the shell out and carefully arrange the stuff so there's no "lumps" and it appears that the shell will fit.  Usually, it's something like that big 8-pin connector pressing down and either flexing boards, or supports.  You may have to shift stuff slightly, and also consider zip-tying it a couple of places to keep them where you want them.

Hi Gary

I just emailed you , but with the guys said above is absolutely correct! This engine has more electronics, and wiring then pretty much any engine Lionel has produced. It’s actually more complicated then the VL Big Boy. Unfortunately trying to locate this short is like trying to find a needle in a haystack. My guess would be its a pinched wire or a protruding solder joint from a circuit board shorting out.

I haven’t serviced  a challenger in quite a while , but in the pictures here , I think there’s suppose to be an insulator over the board ( PCB Regulator) i  took pictures of. I think there might be exposed solder joints on this board. Also there’s a wire with heat shrink Im pointing to. Make sure that’s not squashed.
08A43830-7DE0-41E3-B4A1-CF3F9C99C0365CAF631B-E030-4E1A-ABD4-FD163E92FDA4

Attachments

Images (2)
  • 08A43830-7DE0-41E3-B4A1-CF3F9C99C036
  • 5CAF631B-E030-4E1A-ABD4-FD163E92FDA4
Last edited by Alex M

Hi Alex and Rick I did get a real good deal on it that's why I bought it. I also have the new Visionline Challenger 3717 1931280. I did follow some ideas from gunrunnerjohn and Alex M and I moved the wires around and got the shell back on so now it's running great. I did have problem with the engine speaker wire coming unplugged from the tender so I put a zippy tie on it to hold it in place. I contacted Alex M for help so if something happens I'll send it to him to see what he can do for it in the future. Thanks everyone for your help and advice on this. I'm really Thankful the the OGR Forum is here for the help I've gotten on this.

Gary

Add Reply

Post
This forum is sponsored by Lionel, LLC

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×