Skip to main content

First off, I hope that figurines for the layout are considered as part of the scenery, and that questions regarding the painting of them can be posted on this forum.    If not, then I apologize and the Moderate should just delete this post.

I am using pewter figurines.  I have primed them with duplicolor primer, and then painted the large basic color areas with Testors Enamel Flat model paint.  They look pretty good so far.

I now want to "wash" the figures, before painting on a few fine point details.

My question is, given the paint I have used, what am I suppose to "wash" them with?   What type of paint and what color?


Any advice on that point would be greatly appreciated.

I know that many people would have used different paints and procedures than I have, to get to the wash point. 
But, I really hate to paint, and am doing this as an elementary, down and dirty, job.  Good enough, not great, is my goal.  (Nobody much is ever going to see it beside me anyhow!)

If it is not possible to put a wash coat over Testor's enamel, then that would certainly be helpful info as well.

Thanks very much,

Mannyrock

Original Post

Replies sorted oldest to newest

I know, the traditional advice is to wash cast figures to remove the mold release chemicals. Easy enough if you are patient.

A good friend who is a recognized painter of military figures gave me different advice... just spray prime the figures with a light coat from a black  rattle can of spray paint. The black color gives you a base for facial details, shadows, etc. Use acrylics to then add colors, almost but not quite dry brushing. Let the underlying primer highlight details.

It works for me.

Well, once again, I have not been clear. My fault.

Yes, I washed the  figures with soap and water to remove all chemical residues, before I primed  them.

What I am asking about is the "washing" after application of major colors, using a thin wash coat of brown or gray paint, to create and highlight shadows in the major color areas, before painting on the final fine details.

Thanks,

Mannyrock

@Mannyrock posted:

Well, once again, I have not been clear. My fault.

Yes, I washed the  figures with soap and water to remove all chemical residues, before I primed  them.

What I am asking about is the "washing" after application of major colors, using a thin wash coat of brown or gray paint, to create and highlight shadows in the major color areas, before painting on the final fine details.

Thanks,

Mannyrock

That’s to what suits you,….I use a super thin wash of brown to highlight crevices, folds in their clothing, etc……try gray, brown or black, test on one dude until you’re happy,…volunteer one fella to be the test dummy,….doubt he’ll mind,..😉

Pat

You really need to try different techniques on a test figure or two and see what works for you. I use a wash to tone down everything, create a weathered look. Dry brushing is also important in painting figures...  using acrylics, wipe your brush on a paper towel until very little pigment is on the brush. You can then add subtle colors to the figure with the brush. Another technique...  if you have painted with brash primary colors, consider a light dull coat from the spray can. That gives you 'tooth' for subsequent dry brushing or other techniques.

When I took down an earlier layout I took up painting miniatures.  I mostly use acrylics and there are a number of washes that are available for those.  Vallejo and Citadel make the ones I use, but there are others.  You could try them on enamels but I am not sure that enamel paint has enough tooth for the wash to catch on to.  My concern about making a wash out of enamels is that the base for your wash would likely be a solvent that would break down your underlying paint.

Thanks for all advice.

I have seen some folks say that the put a final sealant coat on their paint jobs, to seal in everything, and they use a spray on polyurethane that has just a little bit of brown color in it.  This also serves as a final darkening wash.   I wonder if this would stick to enamel paint?   Or, if it would just flake off?

I really love enamel paints.  If use any paint that is water soluble, then I am sure to somehow someway get the final product damp or wet somehow, and have the paint come off.  :-(

Mannyrock

Let your newly painted people completely dry up, then use an acrylic wash with a brush that you can control the outcome, I’d think a spray would be hard to get the coloring right,….I use the cheaper acrylics in tubes that artists use, I can thin it down a lot or a little as I see fit,….plus, for just a few bucks, I can get a variety of browns, earth tones, and blacks to make the wash I want for the specific dude I’m detailing,…..a mail man won’t be near as filthy as the dude crawling all over a nasty dirty oily steam locomotive,….😉

Pat

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×