Skip to main content

Hi All,

 

I am looking at building a small subway layout and would like to model the actual subway with station underground and it transition to elevated which is about a 11 or 12" vertical difference and I am limited on space.  What is the max grade a 4 car subway (think the new R-142s) should really be able to handle (straight run up and down) in a layout?

 

Thanks,

 

Chris

Original Post

Replies sorted oldest to newest

Chris-

 

In general, 4-5% is the maximum most O scale trains can handle. Lionel's or MTH's graduated trestle sets would be the maximum grade the cars could handle safely without stalling. However, the steepest grades coming in/out of stations on the "prototype" is about 2%, but there are a few areas where grades exceed 5%.

 

-John

Last edited by AcelaNYP

That math doesn't add up Jerry   1/4 inch a foot adds up to one inch in four feet.   We have a section that is 1/2 inch per foot and a four car train makes it up no problem but six car trains struggle.  Don't go by other trains recommendations because the MTH & Lionel subways are much heavier than normal cars.  Their trucks aren't as free rolling as others too. 

How many inches is the minimum for clearance for the Subway sets?  perhaps if I can limit the rise it will shorten the run I need to make up to the next level.  For example instead of 6" between levels (requires a 12' run @ 1/2" per foot), perhaps I could go 5.5" or 5" which are prototypical 22' and 20' feet and would only require a 11' or 10' run as described earlier.

 

What do you think?

 

Thanks,

 

Chris

Prototype subway tunnel clearances are very tight. The clearances show up well in Toronto because of the light colored station roofs

 

Just make sure it leaves enough room for everything you want to run on the line.  The prototype has cars built to their tunnel dimensions.  We don't have that luxury.

 

EDIT:

 

Here's a diagram from nyc.subway.org showing tunnel dimensions from the Independent Subway. Car dimensions are 60 feet long, 10 feet wide and 12 feet 2 inch car height. Tunnel height is 13 feet 2 inches from the top of the rail to the underside of the tunnel roof.  The article is here.

Last edited by Bill Robb

How many inches is the minimum for clearance for the Subway sets?

 

Lionel's and MTH's subway cars are about 3-3/8" tall (from the top of the rails), so I would recommend at least 3-5/8" minimum clearance to compensate for any track irregularities or at the top/bottom of the grade. Graduated trestle sets top off at anywhere from 4-3/4" (Lionel) to 6" (MTH) tall, which is more than enough for the subways.

 

-JOhn

Here's a diagram from nyc.subway.org showing tunnel dimensions from the Independent Subway. Car dimensions are 60 feet long, 10 feet wide and 12 feet 2 inch car height. Tunnel height is 13 feet 2 inches from the top of the rail to the underside of the tunnel roof.  The article is here.

The R142/R142A cars were built for the IRT Division of the NYC subway, which has more restrictive clearances than the Independent (IND) Division. IRT cars are 51'-4" long versus 60' or 75' on the IND. The IRT tunnels are built to the "Contract 1" part of the diagram from nycsubway.org.

 

-John

 

@AcelaNYP, Yep, the prototype clearances are real tight and I am cool with that, I just don't want to build myself in to a corner if you know what I mean.  That photo is great and the drawings are real helpful.  I think the biggest variances are going to be from the manufacturers Lionel and MTH and trying to be flexible to accomodate the addition of future cars, within reason.

 

Chris

Originally Posted by bluelinec4:

The MTH Premier cars are scale cars   The R62 Railking is scale and the Lionel R27,R30 and R16 are scale.

 

When I get to the club I will measure the Q Cars  This pic shows how tight we went on the R17  There is about 1/4 clearance from the top of the car to the El crossmember

 

 

 

2 001

 

 

2 002If You Don't mind me asking are those elevated structure from bridge boss ? Thanks

 

I use an approximate 3% rise on my personal layout only because I run other heavier Steam Engines besides my Subway sets both Lionel and MTH. I would have to agree that these Subway sets will handle 4-6 % rises rather easily.

See below a few photos of my Elevated graduated and curved sections.

thanks.

jim r

 

 

o500000BC

photos 1-13-12 031

misc 048

Attachments

Images (3)
  • o500000BC
  • photos 1-13-12 031
  • misc 048
Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×