Skip to main content

I want to replace the AC Regulator in my brand new but 12 years old 6-11117 loco. The smoke unit runs but does not respond to Legacy CAB 2 commands for off/low/med/high; it always sputters just a whisp (assuming the loco smoke switch is on.)  Right out of the box. I ordered the correct replacement part, but Lionel sent me something slightly different.  My loco is torn down but I can’t get them to respond to me (it’s been a few days and one call and two emails.)

Photo from their parts listing that I ordered (with 2 black, 1 brown, 1 red wire plus a transistor hanging off).  This matches what’s in my loco:

Photo of what Lionel sent me (note extra wire):

I marked it S03 when I got it, before I realized it was different. Lionel doesn’t list any other regulators that look like this.

Does anyone recognize this?  Thanks!

Attachments

Images (2)
  • What Lionel sent me
  • What I ordered
Original Post

Replies sorted oldest to newest

@Randy P. posted:

I want to replace the AC Regulator in my brand new but 12 years old 6-11117 loco. The smoke unit runs but does not respond to Legacy CAB 2 commands for off/low/med/high; it always sputters just a whisp (assuming the loco smoke switch is on.)  Right out of the box. I ordered the correct replacement part, but Lionel sent me something slightly different.  My loco is torn down but I can’t get them to respond to me (it’s been a few days and one call and two emails.)

Photo from their parts listing that I ordered (with 2 black, 1 brown, 1 red wire plus a transistor hanging off).  This matches what’s in my loco:

Photo of what Lionel sent me (note extra wire):

I marked it S03 when I got it, before I realized it was different. Lionel doesn’t list any other regulators that look like this.

Does anyone recognize this?  Thanks!

imageLooks like the 8volt AC regulator board that I took out of my B&O F3 #6-14569. It’s used to run the 8ohm smoke unit

Attachments

Images (1)
  • image

Steims, thanks so much for your link. I find the last comment from gunrunnerjohn especially interesting: “Note that on Legacy, they finally started bolting the triac to the frame to try to keep it from cooking.  They don't cook as often, but the Legacy ones still fail.”

It sure sounds like they sent me an older version of that unit (I’m guessing the triac is wrapped inside the heat shrink tubing.) Which is unfortunate because I’ve had exactly the problem they were trying to prevent with the upgrade found in my loco. Ugh.

Last edited by Randy P.

Thanks gunrunnerjohn, and also for the suggestion to splice rather than try to rebuild the connectors.
I’m going to hold off on the repair and call Lionel again on Monday as it is frustrating to have to revert to a version of this part that is more likely to fail than the one in my loco which failed immediately (I presume.)

Say, gunrunnerjohn, have you ever tried to repair these AC regulators?  Do you happen to know which part most commonly fails?

I just took a closer look at the one that came in my loco, and suspect my problem was simply related to poor workmanship -- two of the wires were shorted together.  And mine didn't work out of the box.  See attached photo.  I separated the wires but the unit still does not work -- but it got me thinking that it might be repairable -- although failure due to a short might blow a different part than failure due to heat.

Your thoughts appreciated.

Attachments

Images (1)
  • AC regulator S03 lousy workmanship

Chuck, I wrote the S03 on the heat tubing before I realized it was the wrong part - it's not an S03.  It might be an old version and now that I don't have to send the "wrong" ones back I'll cut the tubing and see if the board is similar.  It might be the same as the S03 but with the triac tucked in and a spare ground wire that can be cut - that would be nice!

Regarding smoke fluid, yes, saturated.  I've got the loco apart and took apart the smoke unit and disconnected one side of the resistor to confirm it's 8-ohms, and while I was at it I took out the wick and pulled it apart more and fluffed it back in.  No need to replace as it's brand new with just a touch of brown from my testing.  The resistor is getting some voltage, but not enough to produce more than a polite suggestion of smoke.

I plan to post a summary of everything I've learned once I've got the new unit installed and *hopefully* working.  But it will be a few weeks.

FWIW, I got a bunch of the S03 regulators, and they all appear to be defective.

They start out with an output like this, and the smoke starts as normal.

mceclip1

A few seconds after turning the smoke on, the waveform slowly, it ends up like this within 10-12 seconds.  The smoke vanishes, and yes, I'm using the proper 8 ohm resistor and all the leads are tight, continuity through the wiring is perfect.

Since four of them do this, it's clearly not one defective unit.

As a note, all of these are clearly used, not a truly brand new one in the bunch.

Attachments

Images (2)
  • mceclip0
  • mceclip1
@rplst8 posted:

According to the parts listing, those locomotives use a 6 ohm smoke unit. Unless it's a typo...

https://www.lionelsupport.com/...tive-only-6101117001

https://www.lionelsupport.com/...SSEMBLY-6-ohm-ANALOG

A long time ago Lionel recommended replacing any 6 ohm resistor with an 8 ohm resistor as the excessive power was killing the regulators.  An 8 ohm resistor is the correct resistor to use in any locomotive with this regulator.

Just as a follow-up, Lionel sent me two correct AC Regulators code S03 that matched the one in my loco that was not recognizing Legacy smoke commands.  Tonight I replaced it and now my loco smokes like it should.  So thanks to @gunrunnerjohn for pointing me to that assembly as the likely culprit - it was!

I wish i could repair my old one, but John suspects the likely failing part is the 8-pin surface-mount chip labelled (beneath the S00 label) "MQ4CE RMGKFm", which he says is a microprocessor with custom-flashed code.  And by the way, I don't know if there is any significance to the fact that my old part had a "S00" sticker on the 8-pin chip (i.e. not "S03".)  I looked at the new part that Lionel sent me and that chip has a sticker labelled "S03."

Alas, the 2N6073BG triac is easy to get and easy to replace -- so hoping against hope and with no reason to believe this would be the failing part, I did order a few.  They bolt this thing to the frame so I'm assuming it can get hot.  The next time an S03 regulator goes on one of my locos, I'll try swapping in my bad one with a fresh triac.  Why not?

Anyway, I wanted to let everyone following this thread know that swapping in a new S03 AC regulator fixed the problem of my 6-11117 loco not recognizing Legacy smoke commands.

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×