I would like to know your reason why you put Kadee Couples on your train cars and locos. I don't have the patience to convert everything over and I really think that If I came to a decision to sell the car, someone may not buy it.
Replies sorted oldest to newest
Some reasons I know of are more realistic look (scale size), possibly closer car spacing and they are better for switching operations. You are also correct, they are not for everyone and not everyone would buy a car with Kadee's installed.
1. because they look better
2. because they work better
3. because I WANT to
That's it.... not a long drawn out thought process. You either do or you don't.
I would like to know your reason why you put Kadee Couples on your train cars and locos. I don't have the patience to convert everything over and I really think that If I came to a decision to sell the car, someone may not buy it.
1) They work better! There is no need to bash them together in order to make a coupling, as with those big "lobster claws". I can couple into a single sitting boxcar (weighted to NMRA standards) without having it move and still have a successful joint.
2) They look a whole lot better, especially when body mounted for much closer coupling of cars. The newest Kadee 740 series couplers are even more prototypical in appearance.
3) They STAY COUPLED! Even on very long trains, they STAY COUPLED!
best operating coupler there is! period.
I converted all my HO to it.
I converted all my O scale to it.
Now I'm converting all my G scale to it.
Run out the slack on a hundred car train. Most others will fail or dip out. You'll be sold!
Because you don't need to run at 70 mph to couple them!!
AG.
They work .
I remember back about 1955 when Kadee couplers came out. About the same time the NMRA came out with their stupid design. I couldn't believe what the NMRA did. The Kadees were so slick and looked protypical. Oh, well.
I don't think body mounted Kadees work well on O-31 track. They must have fairly wide radius track. Correct? If I were not a toy train operator, I would consider installing them. The Lionel couplers are OK, but they are not even close to scale. But then, almost nothing is to scale due to space limitations. And 3 rail isn't exactly scale. But 3 rail track and sharp curves and limitations on the amount of track I can fit in a small space doesn't keep me from having a lot of fun with my trains. And fun is the primary objective.
They have problems, too. Have participated in operating sessions on layouts (HO) that
used them. Fiddling was required regularly. These were not amateur layouts, either.
They are a good product, but not perfect - what is?
Frame-mount couplers do not lend themselves to sharper curves. Too bad - getting the coupler off the truck solves more problems than it causes. (Does both.)
Lionel's coupler design works well - and is more prototypical than the Kadees, if you want to pick nits, which I don't. The execution of this design over time by various companies is all over the map, as we know. Some are flawless; some are...the others.
The "70 mph coupling" is neither required nor un-fixable. I have posted more than once the simple fix for most of the "70 mph" units, so I won't do it again. A little analytical thought can come in handy.
I run them because they look better, allow for closer spacing between cars and/or locos, and they are more reliable than lobster claws, which tend to release at random times.
I guarantee you people will still want to buy stuff from you that has been converted to kadees.
I have a small layout with Atlas O-36 curves. On the kits that I build, I use Kadee's. 36' is the longest car I run, though. I use them because I model the late 1800's, early 1900's, which mainly used archbar trucks, which aren't very common in 3-rail. By time you figure the cost plus shipping from Lionel, you're looking at over $20.00 a car for plastic trucks. MTH's parts dept. is completely unworkable, at least for me, so my options are few.
So far the Kadee's work great, look good, and are fairly affordable. For kits, they're also easier to use. Don't have to cut out details to get 3-rail trucks to fit.
My situation is different than most, so I do what I do.
1. because they look better
2. because they work better
3. because I WANT to
That's it.... not a long drawn out thought process. You either do or you don't.
Ditto
Also I can run fifty car trains without having to worry about a lobster claw letting go which they do all the time.
I've never heard of anyone putting a rubber band around their Kadees to keep them closed
I've never heard of anyone gluing their Kadees shut to keep them closed
I've never heard of anyone slamming their cars together to couple the Kadees together
I've never heard of anyone keeping a train permanently coupled because they dislike having to uncouple the cars
Resale value...why do you want to sell your trains?!?!?! When your dead and gone, does it really matter?
I think if Kadee, or any one else, would make a SCALE electric coupler that can be retrofitted replacing the existing claw O couplers, they may make some good money.
I think MTH has HO electrical couplers, not sure why they don't make them O scale too...
Like Doug "Laidoffsick" said:
- They look better. Closer to scale size than the hi-rail coupler. The 700-series look more prototypical than any hi-rail coupler produced.
- They work better. The only uncouple when you want them to. You don't have to slam into them to get them to couple.
- Because you're pulling on the car frame as opposed to the trucks, operation is more natural. You also get the "slack action" on longer trains.
There are some caveats:
- Body-mounted couplers require wider curves. You really shouldn't use them unless you have 36" radius (O-72) curves or larger.
- You'll likely have to adjust the mounting height to get them to the right height on some cars. This is especially true if you're converting hi-rail cars as some of them ride high to compensate for the flanges.
- Unless you convert every single locomotive and piece of rolling stock to Kadees, you'll need a couple of "Transition Cars".
Thought someone should post some photos so here's a Lionel GP9 in Wabash paint with the original coupler sitting behind an Atlas GP9 with Kadee coupler:
Here's the Atlas GP9:
And here's the Lionel GP9 before I repainted it and installed Kadees:
And after:
GP9 1912 was the only Seaboard GP9 to get their light green paint scheme. Warren Calloway provided me with a black and white photo of it in this scheme along with a black and white photo of it in the dark green scheme and you can see the difference in the shades, even in black and white. If there's a color photo of it in the light green scheme it hasn't been published yet.
Attachments
Like Doug "Laidoffsick" said:
- They look better. Closer to scale size than the hi-rail coupler. The 700-series look more prototypical than any hi-rail coupler produced.
- They work better. The only uncouple when you want them to. You don't have to slam into them to get them to couple.
- Because you're pulling on the car frame as opposed to the trucks, operation is more natural. You also get the "slack action" on longer trains.
There are some caveats:
- Body-mounted couplers require wider curves. You really shouldn't use them unless you have 36" radius (O-72) curves or larger.
- You'll likely have to adjust the mounting height to get them to the right height on some cars. This is especially true if you're converting hi-rail cars as some of them ride high to compensate for the flanges.
- Unless you convert every single locomotive and piece of rolling stock to Kadees, you'll need a couple of "Transition Cars".
So basically, if you are running O-27, Traditional, or Hi Rail trains (as the name of this forum might suggest), Kadee couplers don't really have much to offer given the amount of work and cost involved to convert? LOL.
Would I/Do I personally convert to Kadee for 027/Post War trains, and 031 curves? NO
99% of my stuff is scale running on 072 or bigger. 3RS it's still Hi-Rail, and I do convert it all except the passenger cars. Passenger cars get a Kadee on the head end and rear end only for looks. OK so now the rear cars are getting ProtoCraft couplers as they are strictly for looks back there.