Skip to main content

I just scored an example; it's very nice and runs well, but...

...the traction tires look pretty worn and should be replaced; the main valve gear components on the main drivers look to be held in place with some sort of "soldered" affair; how does one go about taking all that stuff off?

Also: this came to me sans tender: anyone out there have a spare or something similar they'd be willing to part with? Ironically, I had (2) extra Lionel E6 tenders, but I gave them to a fellow Forum member...

Thank you.

Mark in Oregon

Mary's Peak

Attachments

Images (1)
  • Mary's Peak
Original Post

Replies sorted oldest to newest

@harmonyards posted:

1. Mark, the eccentrics are held in place by solder only. The eccentric has a square hole, and the end of the crank pin is squared for alignment. If you should decide to disassemble, keep the clock positions noted for reassembly.

2. I believe I’m the one that got that E6 tender from you for a project I had built ……I put it to good use,….😁

1. Thanks for the info; I see a very similar discussion taking place in the 2 rail group... regarding the same engine.

2. Yes, it was you; glad you had a use for it! 👍

Mark in Oregon

Been a long time since i owned one of those engines.  Remember changing the tires without having to unsolder the rods.  If memory serves me right the rod on the front driver is held on with a bolt.  Pretty sure i removed the rod from the front driver and removed the rest of the running gear and rear drivers from the chassi.  Slide the new tires over all of the rods to the wheel sets. Im positive I did not unsolder anything.  Just takes time

Bessemer, I was thinking the same thing as you. Curiosity got the best of me, and I looked for a photo of an E6 online, and from what I could see, the E6 has tires on all 4 drivers. My Williams locos (all with 6 or 8 drivers) have tires on the front and rear drivers only, so there's no need to de-solder anything as you mentioned.

Strummer, what are you going to use for tires? The drivers on these locos have very narrow grooves. I have several of these locos and have been searching for tires that fit.

@Bessemer643 posted:

Been a long time since i owned one of those engines.  Remember changing the tires without having to unsolder the rods.  If memory serves me right the rod on the front driver is held on with a bolt.  Pretty sure i removed the rod from the front driver and removed the rest of the running gear and rear drivers from the chassi.  Slide the new tires over all of the rods to the wheel sets. Im positive I did not unsolder anything.  Just takes time

I kinda get you describe, but in order to apply the new tires onto the main drivers, those side rod assemblies still have to come off, whether the wheel sets are still in the chassis or not, right? 🤔

Maybe I should have "Harmonyards" Pat set this up as a 2 rail engine and just get rid of those d*mn traction tires altogether! 😁

Mark in Oregon

How about a step by step procedure Mark?…desoldering the rods is the easiest way. You can dismantle the engine to get to the tires, but it is a lot simpler to just touch them with an iron and pop them off,….follow the order …

1. remove boiler shell

2. rotate motor by hand so one eccentric is at the 6 o’clock position. Note orientation ( direction eccentric rod faces )

3. hold eccentric with tweezers or needle nose pliers at the small end ( end with the link rod )

4. touch big end of eccentric with soldering iron while lifting upwards.

5. swing eccentric out of the way, lift rod and any spacers off crank pin. ( note how rod & spacers are oriented on crank pin ) you may have to loosen connecting rod bolt on front driver to lift it high enough off rear driver crank pin.

6. replace traction tire

7. place rods & spacers back on crank pin in their correct orientation.

8. grab eccentric with tweezers or needle nose with one hand, and the soldering iron with the other.

9. set eccentric over crank pin in the correct orientation as stated in step 2

10. touch eccentric big end with soldering iron to melt solder, and it will “fall” back in place.  

11. inspect your work. Hold locomotive up and make sure the now freshly soldered eccentric is square …ie; the eccentric face should be parallel with the wheel face. In other words, make sure you didn’t solder it crooked

12. test run engine BEOFRE proceeding to the other side.

13. if step 12 was successful, repeat procedure on the other side

14. job done, prepare peanut butter & jelly sandwich & a glass of milk, ….enjoy

Pat

Last edited by harmonyards

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×