Skip to main content

I have a TMCC Lionmaster Class A SKU: 6-38049 that I was hoping to move from 32 speed steps to 100.  I have 2 questions:

1. From what I have been reading it does sound like that is possible using the ERR Cruise Commander M, is that correct?  Or would I have to replace all the electronics in the engine?

2. I consider myself handy with fixing engines, after reading the install directions it appears that this might even be as simple as moving plugs from the old board to the new one?  Is this upgrade something I should attempt or should I be looking for someone to send the engine to for the upgrade?

Bonus question:  While I'm at it should I attempt to add in a super chuffer or something like that to synchronize the smoke unit with the railsounds?  Or is that too much to take on at once / not possible in the Lionmaster size engine.

Original Post

Replies sorted oldest to newest

The CC-M is a simple install as a rule.  Since this is an Odyssey equipped locomotive, you do have to either do some contact shuffling of the contacts in the Molex plug or splice the supplied plug in.  The Odyssey DCDS has a 6-pin power/motor plug, the CC-M has a 4-pin power/motor plug.  You also have to run the single wire serial data to the R2LC.

Here's the Cruise Commander M Instruction Manual, check out the installation process, you're looking for the Odyssey section for the plug wiring.

The Super-Chuffer II will certainly fit in that locomotive, I've done much smaller stuff.  If you want a prototypical 4-chuff/rev, you could also consider the Chuff-Generator.

The CC-M is a simple install as a rule.  Since this is an Odyssey equipped locomotive, you do have to either do some contact shuffling of the contacts in the Molex plug or splice the supplied plug in.  The Odyssey DCDS has a 6-pin power/motor plug, the CC-M has a 4-pin power/motor plug.  You also have to run the single wire serial data to the R2LC.

Here's the Cruise Commander M Instruction Manual, check out the installation process, you're looking for the Odyssey section for the plug wiring.

The Super-Chuffer II will certainly fit in that locomotive, I've done much smaller stuff.  If you want a prototypical 4-chuff/rev, you could also consider the Chuff-Generator.

Thanks John, that helps a bunch.  Quick question, the super chuffer 2 synchronizes the smoke unit and then the chuff generator syncs the sound, is that the way it works?

Will the Cruise Commander M make that much of a difference, is it worth the cost and effort?

Thanks John, that helps a bunch.  Quick question, the super chuffer 2 synchronizes the smoke unit and then the chuff generator syncs the sound, is that the way it works?

Will the Cruise Commander M make that much of a difference, is it worth the cost and effort?

The difference the Cruise Commander M makes is kinda' up to individual tastes.  The big difference that will be noticeable is typically the low speed steps, you can start slower and accelerate smoother.  Once you're up to around 20-25 scale MPH, I personally don't see much difference between the Odyssey I and the CC-M.

The Super-Chuffer gives you the following features.

  • Synchronized chuffing smoke
  • Smoke at idle (when stopped)
  • Rule-17 LED headlight control
  • Automatic cab light control (off when moving)

You don't have to use the lighting features of the Super-Chuffer if you're not interested in those functions.

The Chuff-Generator is typically used to get 4-chuffs/rev of the drivers vs the 2-chuffs that most TMCC models have.   If you're really into fancy lighting, there is an optional output from the Chuff-Generator for ground lights, they turn off above around 10 scale MPH.

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×