Track binding issue

Are you sure the trains you are using are for the tight 027 turns?

Steam engine, it's a New York Central the engine itself is new old stock has no more than about 20 minutes of run time, is completely clean and it is definitely o27 it seems like the track pinches the drive wheels. It's only through about 5 sections of curve the straight is fine and the other curve sections are fine.

This...

You may have squeezed the track rails together accidentally when putting the track together and caused a "tight gauge" causing the binding.

Remember, it doesn't take much to slow those engines down on curves. It may just be the "natural phenomenon" know as flange bind. I've gotten lots of eye opening experience with it on the toys and the big stuff.

SJC I can say without a doubt that the track is clean and the pins are perfect because I very carefully went over those sections. My longest run between lock ons is 14 sections but the rest are between 5 and 8 sections apart and it doesn't bind at all in the long section so it's not voltage. Which lead me to believe the track rail spacing was pinching the engine and that's why I'm looking for an easy way to respace the rails without replacing the track.

It is likely easier and more economical time and money wise to replace the track as a whole sectional piece than replace the rails or attempt re-gauging them. Used but very serviceable pieces can be had for 25¢ or less at my LHS and train shows.

Replacement is what I was afraid would be my only option it's much more expensive than that around me that's why I was hoping for a spacer tool or something. 

After putting them on top of good pieces every track that binds is slightly rolled like when it was removed from it's previous layout it was just yanked off. I can see the rail turn like a barrel roll very slightly but it is doing it.

AlphaJustin posted:

SJC I can say without a doubt that the track is clean and the pins are perfect because I very carefully went over those sections. My longest run between lock ons is 14 sections but the rest are between 5 and 8 sections apart and it doesn't bind at all in the long section so it's not voltage. Which lead me to believe the track rail spacing was pinching the engine and that's why I'm looking for an easy way to respace the rails without replacing the track.

I didn't say anything about whether or not the track is clean or what the pins are like. I'm talking about squeezing the rails together inward when putting the track together and holding it.

Being that 027 track is so cheap, throw out the problem stuff and go buy a few new pieces. You can build an entire layout with the stuff for $20......

Well, if they can be bent once, they can be bent twice. Get out the pliers!

Nothing magical about this track, it's just sheet metal. Try to make the bad ones match the good ones. Just go slow and be careful how you grab it, so you don't mess up the 'tube' shape or put in a kink. You might even try bending it by hand first.

ALPHAJUSTIN,

Contact me via the email in my profile. I have some O-27 curves I'm not using.

Charlie

Go spend your money and get some Lionel O gauge track. Nick

My experience is that once the track is bent/distorted, it's impossible to get it perfect again. It should be replaced. You might want to figure out how it got bent in the first place and put measures in place so that it does not happen again.

Get an inexpensive end knipper set of pliers and grip the rails just under the rolled top.  Bend them outward ever so slightly, going through each piece a little at a time.  It will take time, but not a lot of money, and you won't have to take up the track.  Don't use too much force, or you will cause a distortion in the rail.  Just go slow and do both sides of each track section.  It should work.  Don't buy the big ended knippers, but get the small ones, about five inches.  They will grab about a half inch of rail with each crimp.  Two pairs working in tandem would be even better.  Just make small adjustments.

   You id early trains by the cab #. That one as NYC #8632  (on the cab), "4-4-2" (wheels front to rear, steam ID system called the "Whyte Notation" "google it" ) Modern era trains use a part number first and foremost, but wheels, train numbers, etc. still get used sometimes too. A "starter set", and not an awful one, but fyi you can expect much more out of the slightly larger 6 driver locos and "hobby grade" loco's in general. Adding weight to the smaller locos usually adds plenty of ability though. Every bit helps and even a half of an once can be noticable   It may need new bushings, etc. earlier; & taxed beyond design, you should watch can motor heat, etc.. If you modify there is always "that one"     or two  but it's too fun to stop  Watching a smaller engine pull like it should is like watching an ant carry a grape   I don't own anything bigger than a 4-6-4 

   Nearly all trains will slow in curves as the flanges rub (except for maybe "digital" engines). More so on 0-27, more so on longer wheel bases, and especially tight are longer ones without blind wheels (flangless). Near every layout will benefit from an extra power drop. I try to add my power feeds near the curves to defeat that.

 Note, minor postion, even an inch, for lock-on change can change the track "sweet spot" for loco performance. Reverse direction Clockwise to C.C., or change to lighted cars, etc., and the sweet spots move again.  Wire conducts easier than track. So add a second or third lock-on, #1 to #1, #2to #2, or solder leads to two spots on the track bottom, sanded clean of plating, etc.. More wire= easier current path, it will give you the smoothest operation. Also check that pins are tight and don't "rattle" in the host track.. You can give them a needle nose crimp on the track into the pin groove from the underside at the web. Try to keep the crimp to the outside of the rail, try not to dent up where flanges rub . A few small inside edge dents isnt gonna kill it, but isn't desirable either. (center rail isn't as much of a concern, no flanges ).

  Eventually, you should look close at your pins. They made hollow ones that do a poor job if they corrode, and they do, and do so from the inside out. Go to solid pins in time, they are cheap enough, especially on the lone center rail because it carries twice the current. Look for a seam on the pin that indicates it is hollow, and or, when you have an extra, hollow ones can usually be crushed flat by pliers. You cant crush a solid pin by hand, if they crush, I pull them and put in a solid one. The hollow pins are thin enough that if corroded, the center pin may glow red hot under normal operation.

  There are "3 rail gauging block", or you can make one by grooving metal or hardwood. Kinda overkill imo, but if you like a tool, you like a tool.

  Also look at the tabs that hold the track on the ties/sleepers. Has the rail shifted? Is the tab set tight? (ties are a pain, rebending those super nicely is almost an art. Tinman sells a set of pliers that do both tabs while supporting the tie bottom.)

Mind the center rail insulators. Look to see those tabs are down and you aren't  bottoming out a roller/shoe and riding up a raised center rail. (which already sits a fraction of an inch higher because it sits on the cardboard insulation... I repair bad insulators with cut up shoe and cereal box flaps. Some stick a strip of elctrical tape on the new insulator too.

There are pliers made just for tube track. Check with the venders in the ads. I rippers made some. I also made a rail bender out of screws, washers, Stanley bracket hardware and a block of wood, dissassembling track and bending it down to 0-17" for a few micro layouts. Nothing is like brand new, so I'll agree with "never the same", but not really so much with buying new track at every hickup.

The " nippers" referred to are called  "side or top cutters". I use modified top cutters. If the handle side jaw area doesn't have a stop, you can grind the cutting edges flat and get at just the rail web (skinny upright part). Mind you a stop means the jaws won't close if you grind on the cutting edges

 I've seen some "linesman pliers" that were ideal.

  O gauge track has bigger pins, slightly taller, fatter ties, 0-31+ (less curve, less slowing). And it is (was?) made of thicker metal than 0-27 so is stronger; strong enough for most folk to stand on. You can reshape track ends and shim 0-27 a bit at the trasitions to combine the two.

  Menard's (online) makes a low cost 31"dia. and bigger tubular O track, while you are looking around. I bought a little, I like mine

  If you buy any straights for expansion, go for the long 30-40", smooth as silk and they have less connections for power to have to cross. Cheaper per inch. Cut with dollar store hack saw if needed and throw the scrap in the box or use the rail as a flat/gondola junk load.

Guys don't complicate things.  Do as Bob Severin suggested and be done with it.

wild mary posted:

Guys don't complicate things.  Do as Bob Severin suggested and be done with it.

Right, we are only talking about 5 curved pieces. No reason not to try Bob's advice first. Make sure the track is screwed down evenly and not overly tightened. Run a longer piece of rolling stock through the section as you work to check your gauge. If that fixes the problem, then you are done! Otherwise, replace the sections.

George

Gentlemen,

   Good Lord 027 track is cheap, purchase and install some new 027 Pieces where ever this is happening thru out your layout.

PCRR/Dave

..... Yea, "buy new" vs bend the rails back and see how it goes. Don't check the retaining tabs that often come loose. Ignore note any other possible issues with 0-27 too. Don't check anything before you screw it down, you'd have no excuse to pull it up again  (sarcasm) 

   I never questioned Bob's advice.    The O.P. was on to the possibility of doing it too.  

  I may be long winded (see "Asperger's Syndrome") but please tell me where I'm incorrect or assumed the O.P. has $30-40 to burn on track, vs a tool that would fix it and be useful in the long run of the hobby.... I gave him a good way to make a better tool, and acknowledged a prefab.

   I mention dulling them and do myself, because my brother cut ours a few times over the years trying to tighten the wrap, vs crimping the notch. The rest is about slowing in curves, or is safety related.

  There is a 3 inch hole an inch deep on my layout melted away by a hollow pin I missed. It didn't melt the grass mat, just the foam under it.  I only found it because it was glowing red hot during a night session.  I knew the hollow pins were weak and got hot, but seeing it was a wake-up.

  Here's more food for thought to complicate life more.

The track might have been fine, within gauge tolorances. 

   But the wheels might be slightly out of gauge; in need of a slight press or tap with wood and a hammer.

  Measured from flange to flange on 2 drivers any wider than 1-1/8" and that could have been the issue, or compounding it.