First layout in 25 years... Attic RR (Update: 9/22/2020)

Good luck and enjoy building the new layout.

MELGAR

Good luck, one recommendation.  If at all possible, try having at least one loop of O72.

Thanks Melgar!!!!  I started building the first of the 4 sections... and, it started to rain!!!  argh!!!  I should be able to carry each section up the spiral staircase to the attic apartment.

I'm with you 100% GRJohn.  I put tape on the floor yesterday and O72 made passage through the apartment a little tight (see photo).   My wife was much happier with O63 (she probably wishes I had stuck with Super-O).  I'm a whisker under 6' tall... the ceiling travels down to 42" where it meets the wall.

Everything under the sheets are trains... that pile is approximately half of my collection.  I don't even really know if I'm a collector... an operator, for sure.

Update: Just finished the jig for the bends @ the front of the bench work (frame) and put the plywood strips in the swimming pool.  I'll pull them out in the morning... and, put them in the jig for 24 hrs.

You can sneak that O72 in there, just move all the tape and she'll never know that it moved over a few inches!

You are the *BEST* GRJ!!!!

Dennis, Congratulations!!!  I had to wait about 25 years between permanent layouts also!  It is a great feeling to get started on on again!!  It looks like a good plan for the attic multi use space!  Make sure you keep your wife happy, but John does have a sneaky idea.    That is really nice how the room is already finished ready for benchwork.  21 feet in length is to die for!!  I'll look forward to seeing your progress!!!  

Thank You Mark!   I finished (sort of) remodeling the apartment a couple of months ago.  It's retro... '53-'64 with modern amenities.  I was born in '53 and the year my Dad bought a 2046 Hudson set for my older brothers.  It is my understanding that '53 was also Lionel's peak year. 

I definitely see the retro look.  Very well done!!!  I was born in '56 and grew up in a house that was 'retro '20s farmhouse'.  That is to say, all was the same as when my dad grew up in the same house except for the '50s appliances Grandma had added when Dad was in the Army.  One of my daughters lives in a house that has a '50s kitchen with new appliances.

I forgot to mention earlier, that pool came in mighty handy for soaking the wood you are going to bend.  I never tried bending wood like that, but I'm looking forward to seeing the great curves your table will have.  I'm hard pressed to get my square corners right on my layout.  

Update: 94F with Heat index of 115F... and, now it's raining.  It would be nice to have a garage.  Anyway, I adjusted the bench work bends to O76 (from O66) ...just in case.  All I would have to do is add about a 10" straight filler piece to the back wall.  Future Proof!   Thanks John!!!

*Homasote*:  I want to cover the entire plywood deck of the bench work.  I just called around and nobody stocks it... before, I order it is there a better product?     Opinions please.

Thank you

Some people use indoor-outdoor carpeting (very tight weave) and some others use 2" or thicker foam board.  Search this forum (or the web) for tips on which product to use and why the user chose that product.  If you still decide to special order Homasote (and many here would go that route), order just enough to go under your track.  Homasote can be cut fairly easily (although quite messy), and using it for scenery base is really just wasting money.

Chuck

Thanks Chuck!  I looked at some *Sound Board* at Lowe's and it seems fine @ 1/3 the price of Homasote.   It's sugar cane fiber and looks like dirt.   I understand it's acoustical properties are minimal but that's not why I'm installing it.   I want the deck to be a somewhat forgiving i.e., *not hard*.  It will sit inside the trim of the bench work so it won't be glued or otherwise attached to the plywood.  Hopefully, I have the bench-work done by next week 9/9-9/10 or so...and, ready for the sound board.

Comments please...

Update:   Rough Bench Work moved up the spiral staircase... man, I'm tired.  I wound up with 7 Sections/Panels and I was allowed to bring the 3 middle sections out to 57" (from 48").  The curved ends are now @ O76 (thanks John) and it holds 220 lbs with ease. My updated bench work plan is attached hereto...

thanks

dennis

Dennis, You are taking a well deserved rest.  The extra width on the curves will be a great asset!  That is a really neat outdoor staircase.  One thing, you didn't have to worry about dinging the walls on the way up with the benchwork!!

Mark, that staircase is 8' in Diameter... I think I built that in 2010.  The largest 2 panels are 4' x 5.5' and it was difficult for me... the first 6 or 7 steps not so bad ...the next 18 or 19 ~~~*Really Tough*~~~!!!!

Here's an update.   I'm waiting for some parts to finish the bench work... but, it's ready for track now!!!

Dennis, Every step is harder than the one before!  We have an indoor staircase that doubles back at the midpoint landing.  It's a pain, and I always catch something on the railing.  Our older daughter and her husband have a similar arrangement in a house twice as old; 100+ versus 52 years.  There is only so much you can get up these.  

What is the great looking white fascia you are using?

I'm in the same boat as your daughter... my house was built in 1905.

Fascia... It's bead board... I put it 1/4" (or so) above the sound board so that ballast, coal and the like stay on the layout (the carpet is brand new).  However, the bead board is pvc... I glued and nailed it to the plywood bends and 1x4s.    I haven't secured the legs yet because I'm waiting for the 2 1/2" carpet/caster cups that I ordered to put under the legs and do final adjustments before I set them permanently.  It's really solid right now though.

PVC beadboard!  That sounds great!!!  The carpet caster cups are a good idea for the legs on that nice carpet.  I grew up in the house my great-grandpa had built in 1888.  I had an HO layout in the dark basement.  I could see it better with two 60 watt incandescent lights than all the 9 LED bulbs today.  

OK... a lot of *thinking*. 

On Tuesday (9/8) I tested Super-O (I still LOVE Super-O), Fastrack and Atlas.  Fastrack was FAST and Easy... and, Atlas was the winner for me.  So, I have a lot of track to sell... and, a couple of LionMasters.  

Yesterday, I started hauling trains upstairs and while I've kept most everything organized there were definitely issues with finding everything.  I got a little frustrated and left everything a mess... and, downloaded SCARM.  Then last night I put together a spread sheet (see below) of where I wanted the Inventory.  Today, I organized everything according to the spreadsheet (and, made sure labeling was easily visible).

I'm still waiting for the carpet/caster cups.  My wife actually wants me to do some *other* things?  I probably will not get the benchwork finished (including benchwork curtains), inventory and sell what I do not need and get the track plan done before the end of the month.   I need a new phone!@!  The lens on the camera is ~~cRUsHEd~~

Thank you for the idea of using the PVC bead board. It provides a clean,  finished, and tapered look. Good luck with your project.