Skip to main content

4 replies

Replacement Trucks to hold Weaver O scale chain drive wheel sets?

K kj356OGR Forum Member SUPPORTING MEMBER

I have some extra Weaver drive systems the old chain drive 1 motor to gear set on the axle and a drive shaft from here to the rear axle drives.

 

I had some ABBA sets and gutted some of the engines so I only had 2 powered engines in each ABBA set of the Weaver FA engine sets.

 

I have some extra gears so split gears is not an issue easy to swap in some spares.

 

But I was thinking of using the left over motors and drives for other engine projects. But I need some truck frames for the old Atlas F9 engines and some Geep kits.

 

So I need the side frame with the detail and some dummy wheels to fit in the old Weaver wheel frames.

 

Any suggestions?

 

Here are pics.

Weaver Silver trucks Atlas old style on left.

 

Atlas has side frames just loose axles held in truck assembly.

Weaver has side frames holding the axle ends.

Last edited by kj356
Original Post

Replies sorted oldest to newest

WoodsworksWoodsworksOGR Forum Member

I am probably risking being excommunicated from this website for saying this....P&D Hobbyshop have Blomberg sideframes - I have a brass set, absolutely exquisite detail.  Precision Scale Co have just about everything imaginable, and they might have their diesel catalogue on-line now, but I can't be sure 'cos I was too busy drooling over their steam catalogue to take any notice ;-)

 

Failing that, dummy locos are always available on E-bay, could maybe find a bargain just for the sideframes?

 

Regards

Paul

Keystoned EdKeystoned EdOGR Forum Member

In addition to their brass EMD Blomburg trucks, P&D offers lower cost plastic ones.  With P&D parts one can readily power/repower Atlas F9's or Red Caboose GP9's.  NWSL sells 40" diameter wheel sets to put under your dummy ALco's.  They also offer geared replacement wheel sets for Weaver drives.  Both P&D and NWSL are "go to suppliers" for O scale diesel  projects.

 

Ed Rappe

P prrjimOGR Forum Member

P&D also had some Alco Plastic truck frame (no wheelsets) in stock.   I think they were old Weaver inventory.    He may be sold out now.

 

I have used this drive in All Nation F Units and switchers using the All Nation trucks.   It worked fine.   

 

The axles and wheelsets seem to be a common 2 rail size, so almost any 2 rail traditional style truck with outside bearings should work (that is the axle actually rides int he side frame).     

Add Reply

Views: 675
Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

Membership Required

We're sorry. You must be signed in to continue. Sign In or Register
×
Are you sure you want to remove from your Block List?
×
Loading...
×
When you block a person, they can no longer invite you to a private message or post to your profile wall. Replies and comments they make will be collapsed/hidden by default. Finally, you'll never receive email notifications about content they create or likes they designate for your content.
Note: if you proceed, you will no longer be following .
×
Link copied to your clipboard.
×

Access to this requires an OGR Forum Supporting Membership

OGR Forum Supporting Membership

Help support this forum with an OGR Forum Supporting Membership.
You will be able to watch the videos in the INSTRUCTIONAL VIDEO FORUM!
A one-year OGR Forum Supporting Membership is only $12 per year, so sign up now!


    OR     


Access the ALL the OGR VIDEO FORUMS AND  over 300 back issues of OGR
with a DIGITAL SUBSCRIPTION!



$12.00 per 12 Months (plus tax if applicable)
×