Skip to main content

  I obtained a new in the box Lionel 844 at the recent York Meet.  The engine performed flawlessly for the past two days.  Today, rather the engine was in the run or program mode, it takes off at full throttle upon the TPC 400 powering up.The Legacy command system runs my other engines with no problems.
I took the shell off, but could not find where  the antenna connects  to the railing?     I would much appreciate any thought on what to look for before sending it back to the dealer for repair.
Thanks in advance
 
 
 
Chris Cook
 
Original Post

Replies sorted oldest to newest

Chrico-

 

The R4LC receiver is definitely in the locomotive, so I would look for either a single yellow or single gray wire coming from the locomotive's motherboard and going to the shell. Sometimes there is a quick disconnect attached to this wire, which is helpful when you need to separate the shell from the chassis.

 

If you see a loose wire that isn't connected to anything, most likely this is the antenna. If so there look for evidence of a broken solder joint somewhere on the inside of the shell; reattach the wire there and it should be back to normal.

 

-John

I discovered that on this particular engine the connection to the handrails is inside the all weather cab.  After removing the two screws holding the cab on, it can be tilted enough to check the connection to the handrails.  I do not know if the connection is soldered or crimped on, but it feels solid. Tomorrow, I will do a continuity check from the connection on the handrails to the mother board.  The black wires from the handrails do go thru a multi wire disconnect 

 

Chris

Last edited by Chrico

Chrico:

 

I have this engine and it is fabulous, but I have had my share of problems with it.

 

1) with the shell off, go to every single circuit board and make sure it is seated properly and firmly to the receptacle.  Sometimes these boards do not seat all the way or come loose when tossed around in a car to/from York.  I fixed my most recent problem that way;

 

2) the handrails are the antennae, and they need to be properly seated in the isolating fittings (at the front of the boiler)- this can be tricky to get right when you reinstall the shell;

 

3) Mine had the opposite problem of not moving at all - it turned out to be a bad control or "mother" board.  Needed to send it back to Lionel for that.

 

Good luck!!  Really great engine once you get it going!

Hopefully, the issue is resolved, but I am not sure why or if the "fix" actually worked or coincidentally worked.

 

  After doing the continuity checks on the antenna system ( no problems indicated by ohm meter), making sure the boards were seated, and inspecting for any electrical connections that may be loose, I but the engine back together with the best of hopes. Bill, I concur with your thoughts on reinstalling the front part of the handrails

 

  Upon powering up the TPC 400, the engine lurched forward with no control.  The engine was seeing the full voltage. Hard to try a reset with the engine racing down the track.

 

The light bulb moment.  To Self:  Why not set the TPC output to a lower voltage.  7 volts worked well.  I set the engine command switch to program and switched on the power to the isolated siding.  Engine moved forward at a slow speed.  Hit the aux 1 boost sequence on the legacy controller for the reset.  Put the engine switch back to run, and all is operating as it should.

 

Since the earlier days of people having runaway engines due to loss of signal from the command base, my engines that are not actively being used sit on electrically switch off sidings/storage tracks.  Thankfully, I have a conditioned reflex on the halt button.

 

The suggestions all of you offered were put to good use and appreciatively added to my knowledge.  Folks such as your selves make this forum rock.

 

Thanks again for your support,

 

Chris Cook

 

 

 

  

Last edited by Chrico

AN update the operational abnormalities of my 844.It is now stuck in reverse, and races rearward for a few seconds to about a minute before it slowly slows down and drops into command mode. Then all of the command functions work in reverse, but the engine will not move forward.  The rear tender light does switch off when a forward command is sent

 

For the purposes of adding to the knowledge base of the forum and also to recognize that some of the more technical minded frequent posters have pointed out the same possible electronic issues in various threads, I have copied the response from Lionel:

 

Christopher,

 

A few other things to have a look at that may cause this issue. If it is darting down the track without any command to move sent you could be looking at a R4LC issue or a DCDS issue. The R4LC is the receiver and acts as the brains of the operation telling everything in the loco what to do. The DCDS is the motor driver. The R4LC talks to the DCDS via a serial wire. If this wire becomes loose or disconnected it will not know what to do and could dart down the track at any time. If the command to move is sent and it darts down the track you could be looking at a flywheel sensor, DCDS or I have seen a few loose flywheels causing an issue like this.

 

 

I will be doing a finale check, then most likely will request an RA for repair. If I had a spare R4LC board, I would give it a try.  It may be worth ordering , since shipping and insurance is about 70 dollars round trip.

 

Hope the information is beneficial  to the group.

 

Christopher Cook

Gunrunnerjohn:

 

  I took the shell off.  I presume the sensor is the part with the symbol of a diode on it.  A small white bar symbol in front of the diode symbol is position directly over the holes in the squirrel cage.  The cage is approximately 1/16 inch from the motor mounted circuit board.

The flywheel and cage are secure.

  Before removing the shell, I powered up the 844.  As the engine ran in reverse with 4 volts applied to the track, the whistle, bell,crew talk etc all worked. Speed control and direction did not. The r reset symbol on the legacy screen was activate, the engine signaled it was received, but nothing changed. I dropped the track voltage to the point of the engine coming to a stop.  I then raised the  track voltage and although the engine would only operated in reverse, it was now under full command control.  Maybe this points more to speed sensor or motor driver issues.  Your thoughts on this would be much appreciated.

 

Chris

 

The fact that it runs in one direction seems to suggest a control issue, that would likely be the DCDS I would suspect.  Since there is some control over the serial link, I'm having a hard time with the R4LC being bad and only affecting forward commands.  I have seen on very rare occasions a speed sensor that only worked in one direction, but that's the exception and not the rule.  My suspicion is the DCDS board if you don't find any wiring issues.  Obviously, if I had it in hand, I'd swap the R4LC first as it's very simple to do, but my betting is on the DCDS.

 

Question.  When it starts flying down the track, does the reverse stop it, or do you have to power off?

 

 

 

 

 

All great information from the guys.  Here is something I have run into.  If someone picks the locomotive up and squeezes the handrails, the handrails pop out of the insulated bushings on the pilot deck.  The bottom of the handrail finds ground and you are not going to be able to run the engine in command.  Replace in bushing and you are good to go.

 

Take your continuity meter and put one probe on the antenna and the other on ground.  Use the siderods for ground.

   Go to this after looking at what the guys posted on.

 

Last edited by Marty Fitzhenry

Thanks for all the suggestion from everyone, but nothing has changed.  I just "fired" it up again. As it has been, it traveled in reverse for about 25 seconds this time and came to a stop on its own.  It then operated in command, but only in reverse.  I can power down power up as many times as I wish, and it will come up in command.  However, if the engines sits for an hour or more unpowered, it will again race of when its powered up.  One might assume a cap is slowing bleeding off during an extended shutdown period?

 

Marty:  I metered the handrails and they are not grounding out.

 

  As it stands now, it is headed for the repair shop. Lionel at 800 miles away, or the nearest authorized repair shop, Charles RO, about 90 miles.  

 

Chris

Last edited by Chrico

Chris, if it goes to Charles Ro, I will end up with it.  Bill, I am with you on the motor sensor.  I have worked on several of those early Legacy engines and the DCDS is less of an issue than the sensor at the flywheel.  Chris, did you meter the handrails to pin 23 on the R4LC?  If you have not done that, put you R4LC probe on the back of the board.

Marty

 

  If looking from the front of the engine to the back, pin 23 is the one on the back row last  on the right, then yes.  I got continuity verification from the handrails to the mother board connection, and then from the handrails to the pin connection.  I used a pin chart that Gunrunnerjohn had posted in an earlier  thread.

 

   Now that I think about the purchase of the engine from a gentlemen in the orange hall this fall, he did say you were one of his go to people for repairs.  

 

Chris

 

 

I Hit the engine with the meter to find 5VDC going into the driver board and no 5VDC coming out to end up at the flywheel encoder.  Replaced the DCDS-J and life is good again in 844 land.

 

That is an early Legacy locomotive with modular boards.  I have run into two in the past that did not produce 5VDC into the DCDS-J and it turned out to be a defective 5 volt regulator that mounts on the motherboard.  Motherboards are cheap and an easy fix. 

 

When troubleshooting these engines, I look for the 5VDC first at the flywheel encored.  If 5VDC is not present there, I go next to the output from the DCDS-J.  If none there I go to the DCDS-J input.   If the DCDS-J input does not have 5VDC the next stop is the motherboard.  The meter is then put on the positive leg of the voltage regulator to look for 5VDC.  If no voltage there, the motherboard needs to be replaced.  Lionel does not recommend taking 5VDC from pins 19 and 20 on the R4LC.   On TMCC engines with an external voltage regulator and a similar issue, if you do not have 5VDC going into the driver board, you can take it from pins 19 and 20 on the R4LC.

Last edited by Marty Fitzhenry

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×