Skip to main content

@Paul Kallus posted:

Is there an approximate runtime before these gear boxes would go bad? And, is anyone performing the fix, and if so about how much would it cost?

Going bad would entirely depend on turns and how long you would run them for. I think Rick said the more turning involved the more the wearing will start, but I forget which way. Regardless, it will wear with more turns back and forth definitely.

Hi Pat,
When you say "early Legacy K4,"  that doesn't mean the pre-war version, I'm assuming??  Just early off of the line?  If I/we take a picture of what we have, can you identify from the pic if it's a possible lemon?

I think he specifically includes the PRR Pre-war model, I have one with that gearbox, the Pennsylvania Prewar LEGACY Scale 4-6-2 K-4 #3667.  I've already swapped the chassis of the identical model for a customer for this issue, that's why Pat has an extra broken chassis!  I keep a spare K4 chassis in the closet, I've already done a few of these over the last few years.

Are we starting a list of known problem models?

I have popped a list of what was considered the possible list on page two John. We haven't really started to compile enough information other than the 2011 K4's with the gearbox issue and the H10 being another potential issue. Rick noted only that the new gearbox design can be noted by looking through the spokes but that doesn't tell what is going on inside of course as Pat and Pete pointed out that some have been modified with the spacer/bracket.

Are we starting a list of known problem models?

That’s what I want this thread to be,….I’ve got the two written down, …the early Legacy K4s, and the Legacy H10,……we’ve excluded a few models, as well, rather than cloud up the list, if it ain’t on the list, it’s good to go,…..I need to learn about the other K4 offerings, like the one in the funeral train set, etc,…..I’d like to do it by item number, so it’s clear as a bell, with out any gray areas…

Pat

I have popped a list of what was considered the possible list on page two John. We haven't really started to compile enough information other than the 2011 K4's with the gearbox issue and the H10 being another potential issue. Rick noted only that the new gearbox design can be noted by looking through the spokes but that doesn't tell what is going on inside of course as Pat and Pete pointed out that some have been modified with the spacer/bracket.

What’s the last K4 offered Dave?….Legacy scale of course,…..

Pat

Thanks Thomas, ….peeking at Dave’s list ( thank you Dave!) I’d say it’s safe to assume all of the 2011 run would be suspect models for problems…..now, what we need to see is all the others,….so we need examples from 2013 to 2018 ….again, I do not want wide spread panic, …..y’all know how this forum can roll,….next thing we know, the sky will be falling……

Pat

@Mikado 4501 posted:

The last one was in 2018 with the long haul tender that headed the 1930 Broadway Limited set, item 6-84816. I think this is also the only one that was included with Bluetooth as of writing.

The Funeral set is after this. However, I have yet to confirm it is missing a bushing like the early ones.

Lionel item # is: 1922030.

@rplst8 posted:

The Funeral set is after this. However, I have yet to confirm it is missing a bushing like the early ones.

Lionel item # is: 1922030.

Here’s the deal, …if you can open yours up, and it’s the same as the 2011 run, then it’s game, set, match, the entire line of K4’s is now suspect to failure, …..if you open yours up, and find a thick spacer next to the worm wheel, opposite the spur gear, then we know we have to back up to find where they made the change……see my point??…

Pat

@harmonyards posted:

Thanks Thomas, ….peeking at Dave’s list ( thank you Dave!) I’d say it’s safe to assume all of the 2011 run would be suspect models for problems…..now, what we need to see is all the others,….so we need examples from 2013 to 2018 ….again, I do not want wide spread panic, …..y’all know how this forum can roll,….next thing we know, the sky will be falling……

Pat

I have both Long Haul Tenders and the Broadway Limited. I just hope I can open them up without cracking stuff to pieces. Fat chance getting it done during the week, it'll have to wait until sometime Saturday. I have the later Mike's offered, the NYC & PRR I think from 2016 as well as the latest ones, I think 4501 in black from 2018?? Where's that list?

@harmonyards posted:

That’s what I want this thread to be,….I’ve got the two written down, …the early Legacy K4s, and the Legacy H10,……we’ve excluded a few models, as well, rather than cloud up the list, if it ain’t on the list, it’s good to go,…..I need to learn about the other K4 offerings, like the one in the funeral train set, etc,…..I’d like to do it by item number, so it’s clear as a bell, with out any gray areas…

Pat

Are we already sure of the H10?

I have both Long Haul Tenders and the Broadway Limited. I just hope I can open them up without cracking stuff to pieces. Fat chance getting it done during the week, it'll have to wait until sometime Saturday. I have the later Mike's offered, the NYC & PRR I think from 2016 as well as the latest ones, I think 4501 in black from 2018?? Where's that list?

Dave, if you’re not comfortable opening them up, don’t do it, …..to be sure there’s plenty of techs and DIY guys that can open one up…..I don’t want folks wrecking their stuff….

Pat

@harmonyards posted:

Judging by what Rick pictured, I’d have to say yes at the very moment,……however, it can be subject to change if we can get one opened up,…..Rick only peeked through the base plate,…..it’d be nice to see that idler shaft from the top view…..

Pat

I went back and reviewed the thread, and I have to say you're right.  I forgot that was the H10, so apparently I have two more than need a "fix".  This is getting absurd!

I liked the sound of the shim you just drop in with the flat side that rides against the gearbox cover to keep it from rotating and/or falling off.  That would be a simple repair.  Drilling holes in the side of the gearbox, OTOH, is a bit more tricky...

I went back and reviewed the thread, and I have to say you're right.  I forgot that was the H10, so apparently I have two more than need a "fix".  This is getting absurd!

I liked the sound of the shim you just drop in with the flat side that rides against the gearbox cover to keep it from rotating and/or falling off.  That would be a simple repair.  Drilling holes in the side of the gearbox, OTOH, is a bit more tricky...

I get it, and I wanted it to be an infield repair as well,…however, by the math, both the sample you had sent, and the first test rig sent by David Ross, there is not going to be a one size fits all solution…..the variance between the two samples was .018…..that’s a lot for a one size fits all solution,……popping a hole in the side of the gear box is child’s play for me,…..so the easiest remedy is a one piece arm that’s both trapped from the gear box cover ( or motor mount if you will ) and a screw to further lock it in place…..the variable is the shim installed on the end of the arm, that’s where I make up the math…….and further, having a bushing on the end of the arm, that rides up against the shaft assembly lessons the drag to the point you don’t even realize it’s there…….David Ross’s showed up with total disengagement, but only had wear similar to the sample you had sent, …..the arm installation put the gear back in the middle, and all is well, ….heck, the worm gear doesn’t even come close to the worn portion now………his locomotive is running well again……it seems these pups start kicking the shaft out and keep on trucking till the worm wheel eventually moves clear out of the way of the worm gear……the screw in the side of the gear box I call cheap insurance…..the part can’t fall off and jam up a gear box and more than likely wipe out a driver…..so the only suck part of this is, yeah, the chassis are gonna have to come to me for fitment, but the plus side for guys like you John, you can strip it down to nothing and send it that way……just like the poor pig you sent me for testing…..but that chassis now you can put back in service,……it will go again…..😉

Pat

@RickO posted:

So who's gonna open up one of those VL 2-10-10-2's?

I believe those have 2 of these reduction gear setups.

Rick, I’d be willing to bet those will be ok,…..we’re clearly seeing an improved gear box as far back as the Legacy Berks, and up to the ATSF Northerns,……the Legacy Mohawks look good too,…..obviously they seen an issue somewhere along the lines, …but doubt we’ll ever get the story,….😉

Pat

Add Reply

Post
This forum is sponsored by Lionel, LLC

OGR Publishing, Inc., 1310 Eastside Centre Ct, Suite 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×